Thermo Products PGL33-250, PGT16-160, PGT5-100 Minimum Clearances to Combustible Materials

Page 6

All installations and services must be performed by qualified service personnel.

- MINIMUM CLEARANCES TO COMBUSTIBLE MATERIALS -

 

MODEL NO.

FROM SIDES

 

FRONT

TOP & SIDES

FROM THE

REAR

BOTTOM

 

 

 

OF FURNACE

 

 

OF PLENUM

FLUE OR

 

 

 

 

 

 

 

 

 

VENT

 

 

 

PGT5-100

1 IN.

 

24 IN.

1 IN.

4 IN.

1 IN.

1 IN.

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

PGT11-125

1 IN.

 

24 IN.

1 IN.

9 IN.

1 IN.

1 IN.

 

 

 

 

 

 

 

 

 

PGT16-160

1 IN.

 

24 IN.

1 IN.

9 IN.

1 IN.

1 IN.

 

 

 

 

 

 

 

PGL20-180

1 IN.

 

24 IN.

1 IN.

18 IN.

1 IN.

N/A

 

PGL33-250

1 IN.

 

24 IN.

1 IN.

18 IN.

1 IN.

N/A

 

 

 

 

 

PGL37-312

1 IN.

 

24 IN.

1 IN.

18 IN.

1 IN.

N/A

 

 

 

 

 

 

 

 

 

 

 

PGL39-400

1 IN.

 

24 IN.

1 IN.

18 IN.

1 IN.

N/A

 

 

The minimum clearances are listed for fire protection. Clearance for servicing the front of the furnaces and to all points on the furnace requiring access must be 24".

Equipment must be installed in accordance with regulations of the National Board of Fire Underwriters. Authorities having jurisdiction should be consulted before installations are made.

C. FURNACE LOCATION AND COMBUSTION AIR

A furnace installed in a residential garage must be installed so the burners and ignition source are located higher than 18 inches above the floor. Also, the furnace must be located or protected to avoid physical damage by vehicles. The furnace must be located on a dry surface. If the surface becomes wet or damp at times, the furnace should be supported above the floor using a concrete base, bricks, patio blocks, etc.

The electrical components of this furnace should be protected against water or moisture.

The area in which the furnace is located must have an adequate supply of air for combustion and draft. Open non-partitioned basements, below grade utility room windows without storms or rooms with loose access doors will generally permit adequate air infiltration. However, if the furnace is located in an area of the building with tight doors and windows, outside ventilation or an opening into another room is recommended. This can be accomplished with two rectangular openings located in a wall or door, one 6" from the ceiling or at the top of the door and one 6" from the floor or at the bottom of the door each having a free area of not less than 1 square inch per 1,000 BTUH input but not less than 100 square inches total. These openings must be free and unobstructed. Maintain a minimum 24" clearance to ventilation openings, which provide combustion air to the furnace.

4

Page 5 Page 7
Image 6
Page 5 Page 7
Contents Models Table of Contents Section Page Page Codes and Clearances II. General InstallationGeneral Instructions Construction MaterialsMinimum Clearances to Combustible Materials Furnace Location and Combustion AIRMAKE-UP AIR VentingExample Vent Dampers Condensing in the ChimneyReplacing AN Existing Furnace from a Common Vent General GAS PipingInstallation of Natural GAS Piping Installation of Liquified Petroleum GAS LP Piping Black Pipe Size for Natural GASTypical Piping for TWO Stage Regulation Burner Installation Copper Tubing Size for Liquified Petroleum GasesTOP View Burner Insertion Illustration PGL TWO Piece Mounting Plate Side View Burner Insertion Illustration PGTMidco RE32 Burner Adjustment Horizontal Furnace PositionsNatural GAS GASDraftoverfire Requirements and Sizing of Duct Work Duct Sizes for HOMES, Quiet Offices or Similar Installations Duct WORK/AIR Conditioning Filters PGT Horizontal Units PGL LowboyFAN and Limit Position and Location Wiring FAN & Limit Location with H-COILLatest Edition Page Page Page Page Latest Edition Operating Instructions Adjustment of BTU Input RateII. Starting the Unit A. Initial Start UP Burner CombustionPage Furnace Checkout Procedure IV. Installers Instructions to UserDealer Maintenance Electrical Cleaning Heat ExchangerVI. Troubleshooting VII. Replacement Parts Page Page

PGL33-250, PGL39-400, PGL37-312, PGT11-125, PGL20-180 specifications

Thermo Products offers a robust lineup of heating devices designed to meet diverse industrial requirements. Among these, models PGL33-250, PGT5-100, PGL39-400, PGL20-180, and PGT11-125 stand out for their innovative technology and exceptional performance.

The PGL33-250 is particularly noted for its high output, making it an ideal choice for larger industrial applications. With an advanced heating element, it ensures rapid temperature increases while maintaining consistent heat distribution. This model is equipped with smart control systems that allow for remote monitoring and adjustments, enhancing operational efficiency.

Next in the lineup is the PGT5-100, a compact yet powerful solution perfectly suited for smaller spaces where efficiency is key. It features an energy-efficient design that reduces operational costs without compromising on performance. The PGT5-100 includes built-in overheat protection, ensuring safe operation even in demanding environments.

The PGL39-400 takes versatility to the next level. Its dual-mode heating capabilities allow users to switch between high-efficiency and high-output settings, catering to varying workload requirements. The advanced insulation technology employed in this model minimizes heat loss, thereby maximizing energy efficiency and reducing environmental impact.

In the mid-range category, the PGL20-180 offers robust performance with a focus on user-friendly features. This model includes a sophisticated digital control panel, providing real-time temperature readings and programmable settings. Its lightweight design makes installation straightforward, while its durability ensures long-term reliability.

Finally, the PGT11-125 stands out for its innovative thermal regulation system. This system adapts the heating output based on real-time environmental conditions, ensuring optimal performance at all times. The PGT11-125 is also constructed using high-quality materials that resist corrosion and wear, making it suitable for various industrial applications.

Collectively, these models from Thermo Products exemplify the company's commitment to quality and technological advancement. With features such as smart controls, advanced insulation, and dual-mode operation, these heating solutions not only offer efficient performance but also contribute to energy savings and a reduced carbon footprint. As industries continue to evolve, Thermo Products remains at the forefront, providing reliable and innovative heating solutions for all industrial needs.
Top Page Image Contents