Thermo Products PGL39-400 General Instructions, II. General Installation, Codes and Clearances

Page 5

All installations and services must be performed by qualified service personnel.

I. GENERAL INSTRUCTIONS

These instructions must be read in their entirety before installing the furnace. It is the installer's responsibility to do the following:

1.Inform and demonstrate to the user, the correct operation and maintenance of the appliance.

2.Inform the user of the hazards of flammable liquids and vapors and to remove such liquids and vapors from the vicinity of the appliance.

II. GENERAL INSTALLATION

These furnaces are shipped with the power gas burner shipped separately. For parts shortage or damage, see the Dealer Receiving and Freight Claim Procedure Section of the price guide. After installation, the furnace and duct system must be adjusted to obtain a temperature rise of 50°F to 80°F through the furnace. The installation must conform with local codes or in the absence of local codes with the National Fuel Gas Codes ANSI Z223.1 LATEST EDITION and to these instructions.

WARNING: This furnace is not to be used as a construction heater.

A. CODES AND CLEARANCES:

The following items must be considered when choosing the size and location of the furnace.

1.All local codes and/or regulations take precedence over the instructions in this manual and should be followed accordingly. In the absence of local codes, installation must conform to these instructions, regulations of the National Fire Protection Association, provisions of National Electrical Code (ANSI/NFPA70 LATEST EDITION), and the National Fuel Gas Code (ANSI Z223.1 LATEST EDITION).

2.The BTU output capacity of the furnace proposed for installation should be based on a heat loss calculation made according to the manuals provided by the Air Conditioning Contractors of America (ACCA) or ASHRAE.

3.The furnace installed is to be level in a central location with respect to outlet registers and should be located near the chimney to minimize the numbers of elbows and the length of any horizontal run of connecting flue pipe which may be required.

4.Definitions of "COMBUSTIBLE MATERIAL" and "NON-COMBUSTIBLE" as issued by

NFPA-Z11-1-3 is as follows:

B. CONSTRUCTION MATERIALS

a. COMBUSTIBLE MATERIAL:

Materials made of or surfaced with wood, compressed paper, plant fibers, plastics or other material that will ignite and burn whether flameproof, fire retardant treated, or plastered.

b. NON-COMBUSTIBLE MATERIAL:

Material which will not ignite and burn; such materials consisting entirely of steel, iron, brick, concrete, slate, glass, plaster or combination thereof.

3

Page 4 Page 6
Image 5
Page 4 Page 6
Contents Models Table of Contents Section Page Page General Instructions II. General InstallationCodes and Clearances Construction MaterialsFurnace Location and Combustion AIR Minimum Clearances to Combustible MaterialsVenting MAKE-UP AIRExample Condensing in the Chimney Vent DampersGeneral GAS Piping Replacing AN Existing Furnace from a Common VentInstallation of Natural GAS Piping Typical Piping for TWO Stage Regulation Installation of Liquified Petroleum GAS LP PipingBlack Pipe Size for Natural GAS TOP View Burner Insertion Illustration PGL Burner InstallationCopper Tubing Size for Liquified Petroleum Gases Side View Burner Insertion Illustration PGT TWO Piece Mounting PlateHorizontal Furnace Positions Midco RE32 Burner AdjustmentDraftoverfire Natural GASGAS Requirements and Sizing of Duct Work Duct Sizes for HOMES, Quiet Offices or Similar Installations Duct WORK/AIR Conditioning PGT Horizontal Units PGL Lowboy FiltersFAN and Limit Position and Location FAN & Limit Location with H-COIL WiringLatest Edition Page Page Page Page Latest Edition II. Starting the Unit A. Initial Start UP Adjustment of BTU Input RateOperating Instructions Burner CombustionPage IV. Installers Instructions to User Furnace Checkout ProcedureCleaning Heat Exchanger Dealer Maintenance ElectricalVI. Troubleshooting VII. Replacement Parts Page Page

PGL33-250, PGL39-400, PGL37-312, PGT11-125, PGL20-180 specifications

Thermo Products offers a robust lineup of heating devices designed to meet diverse industrial requirements. Among these, models PGL33-250, PGT5-100, PGL39-400, PGL20-180, and PGT11-125 stand out for their innovative technology and exceptional performance.

The PGL33-250 is particularly noted for its high output, making it an ideal choice for larger industrial applications. With an advanced heating element, it ensures rapid temperature increases while maintaining consistent heat distribution. This model is equipped with smart control systems that allow for remote monitoring and adjustments, enhancing operational efficiency.

Next in the lineup is the PGT5-100, a compact yet powerful solution perfectly suited for smaller spaces where efficiency is key. It features an energy-efficient design that reduces operational costs without compromising on performance. The PGT5-100 includes built-in overheat protection, ensuring safe operation even in demanding environments.

The PGL39-400 takes versatility to the next level. Its dual-mode heating capabilities allow users to switch between high-efficiency and high-output settings, catering to varying workload requirements. The advanced insulation technology employed in this model minimizes heat loss, thereby maximizing energy efficiency and reducing environmental impact.

In the mid-range category, the PGL20-180 offers robust performance with a focus on user-friendly features. This model includes a sophisticated digital control panel, providing real-time temperature readings and programmable settings. Its lightweight design makes installation straightforward, while its durability ensures long-term reliability.

Finally, the PGT11-125 stands out for its innovative thermal regulation system. This system adapts the heating output based on real-time environmental conditions, ensuring optimal performance at all times. The PGT11-125 is also constructed using high-quality materials that resist corrosion and wear, making it suitable for various industrial applications.

Collectively, these models from Thermo Products exemplify the company's commitment to quality and technological advancement. With features such as smart controls, advanced insulation, and dual-mode operation, these heating solutions not only offer efficient performance but also contribute to energy savings and a reduced carbon footprint. As industries continue to evolve, Thermo Products remains at the forefront, providing reliable and innovative heating solutions for all industrial needs.
Top Page Image Contents