HP PE4240N 42 inch Selecting the input source, Adjusting volume, Muting sound, Using the PIP/POP

Page 30

Selecting the input source

Select the input source for the main picture and the Picture-in-Picture/Picture-on-Picture (PIP/POP) using the front panel buttons or the remote control buttons.

Selecting the main picture input source using the front panel buttons

Press the Input button repeatedly until you see the desired input source. The sources appear in this order: Video1, S-video1, YPBPR1, VGA, DVI, Video2, S-video2, YPBPR2, Channel# (the TV channel).

Selecting the PIP/POP input source using the front panel buttons

Press the Setting button repeatedly until you see the desired input source. The sources appear in this order: Video1, S-video1, Video2, S-video2, YPBPR2.

Selecting the main picture input source using the remote control

Press the TV button (below the remote control indicator light) to select the TV as the controlled home entertainment device, and then press one of these input source buttons at the bottom of the remote control:

•AV selects the input sources connected to the Video Inputs and S-video Inputs, in this order: Video Input 1, Video Input 2, S-video Input 1, S-video Input 2.

•COMP selects the input sources connected to the Component Video Inputs (YPBPR), in this order: Component Video 1, Component Video 2.

•DVI/VGA selects the input sources connected at the DVI or VGA connectors.

•TV selects the input from the TV antenna/cable in connector.

Selecting the PIP/POP input source using the remote control buttons

Press the TV button (below the remote control indicator light) to select the TV as the controlled home entertainment device, press PIP to display the Picture-in-Picture, and then press PIP Input to select the source for PIP.

Adjusting volume

1Press and hold the VOL+ button (on the remote control or on the TV) to increase to the desired level.

2Press and hold the VOL– button (on the remote control or on the TV) to decrease to the desired level.

Muting sound

Press the Mute button on the remote control to cancel the sound; press it again to restore sound.

Using the PIP/POP

This section describes how to view the PIP/POP and how to swap the PIP/POP image with the main picture screen image. To select the PIP/POP input source signal, see “Selecting the input source” on page 26. To learn how to select the display for the PIP/POP, and how to adjust the picture, refer to “Setting up the PIP/POP” on page 41.

Viewing the PIP/POP

On the remote control, press the PIP button to display the PIP mode: PIP (picture inside the main picture), POP-left or POP-right (main picture and PIP shown side-by-side), or PIP off (full screen main picture).

26Using the TV

Page 29 Page 31
Image 30
Page 29 Page 31
Contents HP PE4240n 42 Plasma Television User’s Guide USA Table of Contents Troubleshooting Specifications First SafetyInstalling the TV Opening the packagePrecautions Cleaning the TV Wall Mounting or Stand Replacement Preventing Image RetentionWhat is in the Box FeaturesIntroduction Page Identifying front panel controls and indicators OverviewIdentifying the remote control buttons MTS AV, COMP, DVI/VGA, TV Identifying connectors Rear view/terminal board IntroductionProtection Set Up Attaching and Connecting Optional External SpeakersAttaching the speakers to the TV Connecting the speakers to the TV Connecting an Antenna or Cable TV Connecting an antenna or cable directly to the TVConnecting a set-top-box to the TV Connecting a digital TV DTV receiver to the TVPage Connecting a Composite Video Source Connecting an S-Video Source Connecting a Component Source Connecting the HP Media Center PC Using the HP Mcpc with the TV remote controlHP.PC TV remote HP Mcpc button Button FunctionDVI/VGA HP.MC Installing or Replacing Remote Control Batteries Using the TV Front Panel ButtonsBasic Operations Turning on the TVTurning off the TV Selecting the input source Adjusting volumeUsing the PIP/POP Muting soundSwapping the PIP/POP with the main screen image Using the sleep timer to turn off the TVSelecting the screen aspect Image area Ratio DescriptionUsing the On Screen Display OSD Controls Using the OSD menus Picture menu Function Default ResetDisplay menu Function Default Reset Sound menu Function Default Reset Function Default Reset MenuConfiguration Function Default Reset Menu Information menu Function Default ResetTV Setup menu Function Default Reset Changing the OSD Settings Setting up TV channels Auto ScanRun auto scan Page Add or delete a channel Set up favorite channel Fine tuning a channel Mapping channels Page Adjusting the picture How to adjust the main pictureSetting up the PIP/POP How to automatically adjust the picture for VGA inputAdjusting sound settings Selecting the speaker source Selecting SAPUsing the screen washing feature Selecting Auto Off mode Setting up V Chip Changing the V Chip settingsPage Changing the V Chip PIN Page Using closed caption Setting up VGA Selecting color systemUsing the Remote Control Programming the remote control for component control Programming the component codeSearching for the component code Checking the component code Reassigning component buttonsTo assign Use this sequence Changing volume lock Troubleshooting the remote control programmingProblem Solution Manufacturer’s codes Manufacturer Codes for VCRCCE KEC HI-QJVC KLHRCA STSTMK Manufacturer Codes for cable converter box ABCNSC Popular Mechanics 0400 Proscan 0021 Pulsar 0000 Quasar Manufacturer Codes for satellite or DBS receivers HTSManufacturer Codes for DVD players Troubleshooting Symptom Checks RemedyOperate the external device or computer move Picture SpecificationsSignals Input terminalsConnector Specifications Pin VGA Signal analog NumberPin assignments and signals for DVI-D connector Pin DVI-D Signal digital NumberModifications Agency Regulatory NoticeFederal Communications Commission Notice CablesIndex HP McpcPIP/POP Index Page Page
Related manuals
Manual 8 pages 58.48 Kb Manual 1 pages 756 b
Top Page Image Contents