HP PE4240N 42 inch Agency Regulatory Notice, Federal Communications Commission Notice, Cables

Page 73

Agency Regulatory Notice

Federal Communications Commission Notice

This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:

Reorient or relocate the receiving antenna.

Increase the separation between the equipment and receiver.

Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.

Consult the dealer or an experienced radio or television technician for help.

Modifications

The FCC requires the user to be notified that any changes or modifications made to this device that are not expressly approved by Hewlett-Packard Company may void the authority to operate the equipment.

Cables

Connections to this device must be made with shielded cables with metallic RFI/EMI connector hoods in order to maintain compliance with FCC Rules and Regulations.

Declaration of Conformity for products marked with the FCC logo – United States only

This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) this device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation.

For questions regarding your product, contact:

Hewlett-Packard Company

P.O. Box 692000, Mail Stop 530113

Houston, Texas 77269-2000

Or call: 1-800-652-6672

For questions regarding this FCC declaration, contact:

Hewlett-Packard Company

P.O. Box 692000, Mail Stop 510101

Houston, Texas 77269-2000

Or call: (281) 514-3333

To identify this product, refer to the part, series, or model number found on the product.

Agency Regulatory Notice 69

Image 73
Contents HP PE4240n 42 Plasma Television User’s Guide USA Table of Contents Troubleshooting Specifications Installing the TV SafetyFirst Opening the packagePrecautions Cleaning the TV Preventing Image Retention Wall Mounting or Stand ReplacementFeatures What is in the BoxIntroduction Page Overview Identifying front panel controls and indicatorsIdentifying the remote control buttons MTS AV, COMP, DVI/VGA, TV Rear view/terminal board Introduction Identifying connectorsProtection Attaching and Connecting Optional External Speakers Set UpAttaching the speakers to the TV Connecting the speakers to the TV Connecting an antenna or cable directly to the TV Connecting an Antenna or Cable TVConnecting a digital TV DTV receiver to the TV Connecting a set-top-box to the TVPage Connecting a Composite Video Source Connecting an S-Video Source Connecting a Component Source Using the HP Mcpc with the TV remote control Connecting the HP Media Center PCDVI/VGA TV remote HP Mcpc button Button FunctionHP.PC HP.MCInstalling or Replacing Remote Control Batteries Front Panel Buttons Using the TVTurning on the TV Basic OperationsTurning off the TV Using the PIP/POP Adjusting volumeSelecting the input source Muting soundSelecting the screen aspect Using the sleep timer to turn off the TVSwapping the PIP/POP with the main screen image Image area Ratio DescriptionUsing the On Screen Display OSD Controls Picture menu Function Default Reset Using the OSD menusDisplay menu Function Default Reset Function Default Reset Menu Sound menu Function Default ResetInformation menu Function Default Reset Configuration Function Default Reset MenuTV Setup menu Function Default Reset Setting up TV channels Auto Scan Changing the OSD SettingsRun auto scan Page Add or delete a channel Set up favorite channel Fine tuning a channel Mapping channels Page How to adjust the main picture Adjusting the pictureHow to automatically adjust the picture for VGA input Setting up the PIP/POPAdjusting sound settings Selecting SAP Selecting the speaker sourceUsing the screen washing feature Selecting Auto Off mode Changing the V Chip settings Setting up V ChipPage Changing the V Chip PIN Page Using closed caption Selecting color system Setting up VGAUsing the Remote Control Programming the component code Programming the remote control for component controlSearching for the component code Reassigning component buttons Checking the component codeTo assign Use this sequence Troubleshooting the remote control programming Changing volume lockProblem Solution Manufacturer Codes for VCR Manufacturer’s codesCCE JVC HI-QKEC KLHSTS RCATMK ABC Manufacturer Codes for cable converter boxNSC Popular Mechanics 0400 Proscan 0021 Pulsar 0000 Quasar HTS Manufacturer Codes for satellite or DBS receiversManufacturer Codes for DVD players Symptom Checks Remedy TroubleshootingOperate the external device or computer move Signals Specifications Picture Input terminalsPin VGA Signal analog Number Connector SpecificationsPin DVI-D Signal digital Number Pin assignments and signals for DVI-D connectorFederal Communications Commission Notice Agency Regulatory NoticeModifications CablesHP Mcpc IndexPIP/POP Index Page Page
Related manuals
Manual 8 pages 58.48 Kb Manual 1 pages 756 b