HP PE4240N 42 inch manual Safety, First, Opening the package, Installing the TV

Page 5

Safety

First:

Read all instructions before installing and operating the TV.

Keep this user guide in a safe place for future reference.

To reduce the risk of bodily injury, electric shock, fire, and damage to the TV, observe all warnings and precautions in this user guide.

Do not use attachments that are not recommended by HP with this product. Use of inadequate attachments may result in damage to the product or personal injury.

Follow all instructions.

Opening the package:

Due to the size and weight of the TV, it is recommended that a minimum of two people move it.

Whenever possible, use the handles on the back of the TV for transport.

If speakers are attached to the TV, do not lift the TV by the speakers; instead, use the handles and the area under the screen.

The protective glass and the glass substrate are installed on the front of the TV. Because both glasses can be broken and scraped easily, move the product gently. Never place the TV with the glass facing downward, unless it is protected with pads.

The TV is packaged in a carton with other standard accessories. When opening the carton, check that the TV is in good condition and that all standard accessories and items are included. Any optional accessories come separately in another carton.

Installing the TV:

A specified technician from the distributor or authorized agent should install the TV. Refer to “Wall Mounting or Stand Replacement” on page 4 for more information.

Install the TV on a flat surface to avoid tipping. Leave some distance between the back of the TV and the wall for proper ventilation. Never install the unit where the ventilation on the top of the TV is covered. Otherwise, fire or damage to the unit may occur.

Avoid installing the TV in the kitchen, the bathroom, or any other area with high humidity. Damp conditions may shorten the service life of the electronic components, or may cause fire or electrical shock.

Route power and signal cords appropriately to avoid stepping or tripping on them.

Do not install this TV outdoors; rain or extended direct sunlight may damage the unit.

Do not install the TV in a vehicle; vibrations may damage the unit, or the unit may fall and cause injury.

Do not install the TV in a ship or a vessel; seawater damages the unit and may start a fire.

Install the TV horizontally; any 90-degree clockwise or counterclockwise installation may induce poor ventilation and subsequent component damage. Do not hang the TV from the ceiling; the unit may fall and cause injury.

Do not install near appliances, such as a microwave.

Do not install near a heat source, such as a fireplace or radiator.

Safety 1

Image 5
Contents HP PE4240n 42 Plasma Television User’s Guide USA Table of Contents Troubleshooting Specifications Installing the TV SafetyFirst Opening the packagePrecautions Cleaning the TV Preventing Image Retention Wall Mounting or Stand ReplacementIntroduction What is in the BoxFeatures Page Overview Identifying front panel controls and indicatorsIdentifying the remote control buttons MTS AV, COMP, DVI/VGA, TV Rear view/terminal board Introduction Identifying connectorsProtection Attaching and Connecting Optional External Speakers Set UpAttaching the speakers to the TV Connecting the speakers to the TV Connecting an antenna or cable directly to the TV Connecting an Antenna or Cable TVConnecting a digital TV DTV receiver to the TV Connecting a set-top-box to the TVPage Connecting a Composite Video Source Connecting an S-Video Source Connecting a Component Source Using the HP Mcpc with the TV remote control Connecting the HP Media Center PCDVI/VGA TV remote HP Mcpc button Button FunctionHP.PC HP.MCInstalling or Replacing Remote Control Batteries Front Panel Buttons Using the TVTurning off the TV Basic OperationsTurning on the TV Using the PIP/POP Adjusting volumeSelecting the input source Muting soundSelecting the screen aspect Using the sleep timer to turn off the TVSwapping the PIP/POP with the main screen image Image area Ratio DescriptionUsing the On Screen Display OSD Controls Display menu Function Default Reset Using the OSD menusPicture menu Function Default Reset Function Default Reset Menu Sound menu Function Default ResetInformation menu Function Default Reset Configuration Function Default Reset MenuTV Setup menu Function Default Reset Run auto scan Changing the OSD SettingsSetting up TV channels Auto Scan Page Add or delete a channel Set up favorite channel Fine tuning a channel Mapping channels Page How to adjust the main picture Adjusting the pictureHow to automatically adjust the picture for VGA input Setting up the PIP/POPAdjusting sound settings Selecting SAP Selecting the speaker sourceUsing the screen washing feature Selecting Auto Off mode Changing the V Chip settings Setting up V ChipPage Changing the V Chip PIN Page Using closed caption Selecting color system Setting up VGAUsing the Remote Control Searching for the component code Programming the remote control for component controlProgramming the component code To assign Use this sequence Checking the component codeReassigning component buttons Problem Solution Changing volume lockTroubleshooting the remote control programming CCE Manufacturer’s codesManufacturer Codes for VCR JVC HI-QKEC KLHSTS RCATMK NSC Manufacturer Codes for cable converter boxABC Popular Mechanics 0400 Proscan 0021 Pulsar 0000 Quasar HTS Manufacturer Codes for satellite or DBS receiversManufacturer Codes for DVD players Symptom Checks Remedy TroubleshootingOperate the external device or computer move Signals SpecificationsPicture Input terminalsPin VGA Signal analog Number Connector SpecificationsPin DVI-D Signal digital Number Pin assignments and signals for DVI-D connectorFederal Communications Commission Notice Agency Regulatory NoticeModifications CablesHP Mcpc IndexPIP/POP Index Page Page
Related manuals
Manual 8 pages 58.48 Kb Manual 1 pages 756 b