HP FC 1GB/2GB 16B manual General Specifications, Table A-4, Specification Description

Page 40

A

Product Specifications

Table A-3Environmental Requirements (Continued)

Shock (operating)	4G, 11MS duration, half sine

Shock (non-operating)	20G, 11MS duration, sq.wave

Vibration (operating)	5G, 0-3 kHz at 1.0 octave/minute

Vibration (non-operating)	10G, 0-5kHz at 1.0 octave/minute

General Specifications

The FC 16B supports F_Port, FL_Port, and E_Port connections and DNS (Distributed Name Server). It is EMC (Electromagnetic Compatibility) compliant.

The following table lists the general specifications for the FC 16B.

Table A-4	General Specifications

Specification		Description

Configurable port types		The FC 16B supports F_Port, FL_Port, and E_Port
		connections.

EMI rating		An operating FC 16B conforms to the EMI (electromagnetic
		interference) radiation levels specified by the following
		regulations:
		• FCC Rules & Regulations, Part 15B, Class A level
		•	CISPR22 Class A
		•	EN55022 Class A
		• VCCI Class A ITE
		• AS/NZS 3548 Class A

System architecture		Non-blocking shared-memory switch

System processor		Intel 80960VH, 100MHz CPU

ANSI Fibre Channel protocol		FC-PH (Fibre Channel Physical and Signalling Interface
		standard)

Modes of operation		Fibre Channel Class 2 and Class 3

Fabric initialization		Complies with FC-SW 5.0

FC-IP (IP over Fibre Channel)		Complies with FC-IP 2.3 of the FCA profile

Aggregate switch I/O bandwidth		64 Gbps if all 16 ports running at 2Gbps, full duplex

Frame buffers		27 buffers per E_Port and 16 buffers per F_Port at 2112 bytes
		per frame

A-4	HP Surestore FC 1Gb/2Gb Switch 16B Installation and Reference

Image 40

Contents

Page Warranty Contents Glossary Index Preface About This GuideRelated Publications Getting HelpGetting Software Updates Use of Notes, Cautions, and WarningsViii Switch 16B Introducing the HP Surestore FC 1Gb/2GbOverview SFP Media Side Monitoring and Managing the FC 16B Introducing the HP Surestore FC 1Gb/2Gb Switch 16B FC 1Gb/2Gb Switch 16B Installing and Configuring the HP SurestoreSafety Guidelines Package Contents Installing the Switch as a Stand-Alone UnitInstalling the Switch in a Rack FC 16B Rack-Mounted SwitchPage To install the switch in a rack Installing the Rear Rail-Tray Brackets HP RackInstalling the Tinnerman Clips HP Rack Installing the Rubber Washers Assembling the Inner Rails Configuring and Connecting the Switch To configure the FC 16B and connect it to a fabricA Windows 95, 98, 2000, or NT environment Page Saving the System Configuration Files Backing up the Switch Configuration Settings Setting QuickLoop Mode on Ports Next StepsHP Surestore VA Private Loop Devices Turning the FC 16B On and Off Operating the HP Surestore FC 1Gb/2Gb Switch 16BInterpreting LED Activity LEDs On the SFP Media Side Above LEDs On the Power Supply Side Interpreting Post Results SupplyMaintaining the Switch Diagnostic TestsField-Replaceable Units FRUs Operating the HP Surestore FC 1Gb/2Gb Switch 16B Product Specifications Switch ComponentsWeight and Physical Dimensions Dimension ValueFacility Requirements Table A-1Power Supply Specifications Environmental RequirementsSpecification Description General SpecificationsTable A-4 Optical Port Specifications Memory SpecificationsSerial Port Specifications Signal Description Post SpecificationsPIN Regulatory Compliance FCC EMC Statement USA EMC Statement CanadaCertification and Classification Information Product Information Declaration of Conformity Glossary Credit Cut-through Data Word Defined Zone Configuration BERBlock BroadcastDLS EdtovFC-AL-3 FC-FLA FCP FC-PH-1, 2, 3 FC-PI FC-PLDA FC-SW-2 FlogiFRU FSPFspf GbicHBA IODJbod LIP LmtovLpsm LWL MIBPlogi PostRatov RAIDRrtov RscnSNS SnmpSWL UDP ULP Ulptov WWNIndex EMINvram A-2 Index-3 Index-4