HP R5500 manual Class a equipment, Class B equipment

Page 53

Class A equipment

This equipment has been tested and found to comply with the limits for a Class A digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference when the equipment is operated in a commercial environment. This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. Operation of this equipment in a residential area is likely to cause harmful interference, in which case the user will be required to correct the interference at personal expense.

Class B equipment

This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:

Reorient or relocate the receiving antenna.

Increase the separation between the equipment and receiver.

Connect the equipment into an outlet on a circuit that is different from that to which the receiver is connected.

Consult the dealer or an experienced radio or television technician for help.

Declaration of conformity for products marked with the FCC logo, United States only

This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions:

(1)this device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation.

For questions regarding this product, contact us by mail or telephone:

Hewlett-Packard Company

P. O. Box 692000, Mail Stop 530113 Houston, Texas 77269-2000

1-800-HP-INVENT (1-800-474-6836). (For continuous quality improvement, calls may be recorded or monitored.)

For questions regarding this FCC declaration, contact us by mail or telephone:

Hewlett-Packard Company

P. O. Box 692000, Mail Stop 510101 Houston, Texas 77269-2000

1-281-514-3333

To identify this product, refer to the part, series, or model number found on the product.

Regulatory compliance notices 53

Image 53
Contents HP UPS R5500 User Guide Audience assumptions Contents Spares Warranty information UPS R5500 overview Component identificationUPS front panel This sectionFront panel is shown with the bezel removed UPS front panel controlsUPS front panel LED indicators Repo port UPS rear panelERM rear panel Preparing to install the hardware InstallationPrecautions Readying the equipment Tools and materialsSelecting a site Installing the mounting rails Installation Preparing the rails for integrated shipping Installing the UPSRemoving the UPS battery bracket Installing the batteries Replacing the UPS battery bracket Installation Connecting the Repo port Installation Connecting devices to the UPS Connecting the ground bonding cableConnecting the UPS to utility power Installation Starting power to the load Installing the ERMInstallation Installation Operate mode Standby modeUPS operations Modes of operationAuto-Bypass mode Configuring the UPSConfigure mode Silencing an audible alarm Testing the LEDsVerifying the Repo port connection Powering down the UPSPower management software Power managementRemoving the UPS front bezel MaintenanceMaintenance Replacing the UPS option card Replacing the batteries Important battery safety informationBattery care and storage guidelines Replacing the UPS UPS battery replacement procedureReplacing the ERM Updating the UPS firmware LED and audible alarm troubleshooting TroubleshootingBypass is out of range Battery conditionInternal UPS fault condition General alarm conditionInput voltage is out of range Insufficient warning of low batteriesSite wiring condition Low battery shutdownsUPS does not provide the expected backup time Overload conditionUPS is in Auto-Bypass mode UPS frequently switches between utility and battery powerUPS is on battery Utility power conditionUPS physical specifications SpecificationsERM physical specifications UPS input specificationsVoltage specifications UPS output specificationsPower protection specifications Battery runtime for NA/JPN model Battery specificationsBattery runtime for Intl model Output tolerance specificationsRepo port specifications Environmental specificationsOrdering spares UPS spare parts listSpares Hardware options HP contact information Technical supportBefore you contact HP Limited warranty Warranty information$250,000 Computer Load Protection Guarantee Pre-Failure Battery WarrantyNotification from power management software Regulatory compliance identification numbers Regulatory compliance noticesFederal Communications Commission notice FCC rating labelClass B equipment Class a equipmentCables ModificationsCanadian notice Avis Canadien European Union regulatory noticeJapanese notice Bsmi notice Battery replacement notice Power cord statement for Japan Taiwan battery recycling noticeGrounding methods to prevent electrostatic discharge Electrostatic dischargePreventing electrostatic discharge Acronyms and abbreviations Index On button, location Operate mode Index
Related manuals
Manual 61 pages 14.43 Kb