HP SL500 (M852x) manual Abstract, Product Version Supported Release Version Updates RVUs

Page 1

SL500 (M852x) Tape

Library Installation and

User’s Guide

Abstract

This manual describes how to install and use an M852x tape library on HP NonStop™ servers.

Product Version

N.A.

Supported Release Version Updates (RVUs)

This publication supports G06.31 and all subsequent G-series RVUs and H06.11 and all subsequent H-series RVUs until otherwise indicated by its replacement publication.

Part Number	Published

541531-006	June 2007

Image 1

Contents Abstract Product Version Supported Release Version Updates RVUsPart Number Published Document History Part Number Product Version Published Overview of the Tape Library SL500 M852x Tape Library Installation and User’s GuideCartridge Information Tables FiguresContents Manual Information What’s New in This ManualNew and Changed Information Document HistoryPage Notation Conventions About This ManualHypertext Links Change Bar NotationViii This section includes Overview of the Tape LibraryFront View of Tape Library Components Views and LocationsBack View of Tape Library Components Physical Configurations Base Module Slots Slots Locations for Firmware Slot Mapping Slots Locations for Scsi Element Numbering Mapping Slot Capacity for Back Wall of Cartridge Expansion Module Capacities CAP Robotics Unit Robotics Components Hand Assembly Fans ElectronicsRLC Card Interface CardsCartridge Access Port Power SystemCAP Condition Specification Performance LTO Generation 3 SpecificationsSupported Tape Drives LTO UltriumCards and Power Supply Safety FeaturesAudit of Tape Library Robotics10. Tape Library Interfaces Locations InterfacesPower Switch Controls and IndicatorsKeypad Buttons and Indicators Buttons/Indicators Description Keypad Buttons and IndicatorsIndicator ButtonPage Opening the Front Door With Power Automated ModeSecuring the Front Door With Power Library OperationSliding a Magazine Into a CAP Powering Off the Tape Library Powering On the Tape LibraryOpening the Front Door Without Power Manual ModeDoor Locking Lever Extended Securing the Front Door Without PowerInsert Cartridges Into Slots Locate and Remove CartridgeInserting Cartridges Into Slots Inserting Cartridge Into Tape Drive Inserting a Cartridge Into a Tape DriveLocation of Unload Button Removing a Cartridge From a Tape DriveRemoving a Cartridge From the Gripper Assembly Manual Release Screw Replacing a Cleaning CartridgePage Handle Cartridges Cartridge InformationInspect Cartridges Maintain Cartridges Apply Cartridge Labels Ultrium CartridgesValid Labels Label Type of Cartridge LTO Cartridge CodesUltrium Cartridge Label Write-Protect Switch Setting the Write-Protect SwitchSpecification L3 Cartridge L2 Cartridge L1 Cartridge LTO Gen 1, Gen 2, and Gen 3 Cartridge SpecificationsPage Adding the Control Path and the Data Path Supported ConnectionsServerNet/DA To add the data path PMF CRU PMF CRU Adding the Control Path and Data Path Supported ConnectionTo add the data path SCF, issue this command Configuration Overview Series Rear View System Configuration Example Fiber-opticAdding the Control Path and Data Path Page Figure A-1. Library and Rack Dimensions SpecificationsFigure A-2. Tape Library and Rack Dimensions Table A-1. Library Component Weights Tape Library Components WeightsTable A-2. Library Environment Specifications Tape Library EnvironmentPower Cord Numbers and Receptacles PowerTable A-3. Power Cord and Receptacles Table A-4. Non-Country-Specific CordsInstalling the Power Cords Figure A-3. Power Cabling Table A-5. Power for Library Without Tape Drives Power SpecificationsTable A-6. Power for Base Unit and Two LTO Tape Drives Page Regulatory Compliance Statements Safety and ComplianceFCC Compliance Canadian ComplianceStatements-2 Laser Compliance European Union NoticeSafety Caution High Leakage Current Waste Electrical and Electronic Equipment WeeeSafety