HP SL500 (M852x) manual Controls and Indicators, Power Switch, Keypad

Page 29

2 Controls and Indicators

This section includes:

Power Switch	2-1
Keypad	2-1

Power Switch

When the switch is in position 1 the tape library and tape drives are powered on. When the switch is in position 0 the tape library and tape drives are powered off.

Note. Earlier built tape libraries had power supplies that had individual power switches. Later tape libraries have one power switch that controls all power supplies in the rack.

Keypad

The keypad is used to open the door, open the CAP, and notify the user if service is required.

1.The Door Open button opens the tape library door. All doors function as one door and can not be opened individually.

2.The CAP Open button opens all CAP doors.

3.The Library Active LED, if on, indicates the tape library is functioning properly. If the Library Active LED is flashing, call your service representative.

4.If the Service Robot LED is on and flashing, call your service representative.

5.If the Service Required LED is on and flashing, call your service representative.

SL500 (M852x) Tape Library Installation and User’s Guide—541531-006

2-1

Image 29

Contents Part Number Published Product Version Supported Release Version Updates RVUsAbstract Document History Part Number Product Version Published Overview of the Tape Library SL500 M852x Tape Library Installation and User’s GuideCartridge Information Tables FiguresContents Manual Information What’s New in This ManualNew and Changed Information Document HistoryPage Notation Conventions About This ManualHypertext Links Change Bar NotationViii This section includes Overview of the Tape LibraryFront View of Tape Library Components Views and LocationsBack View of Tape Library Components Physical Configurations Base Module Slots Slots Locations for Firmware Slot Mapping Slots Locations for Scsi Element Numbering Mapping Slot Capacity for Back Wall of Cartridge Expansion Module Capacities CAP Robotics Unit Robotics Components Hand Assembly Fans ElectronicsRLC Card Interface CardsCAP Condition Power SystemCartridge Access Port Specification Performance LTO Generation 3 SpecificationsSupported Tape Drives LTO UltriumCards and Power Supply Safety FeaturesAudit of Tape Library Robotics10. Tape Library Interfaces Locations InterfacesKeypad Controls and IndicatorsPower Switch Buttons and Indicators Buttons/Indicators Description Keypad Buttons and IndicatorsIndicator ButtonPage Opening the Front Door With Power Automated ModeSecuring the Front Door With Power Library OperationSliding a Magazine Into a CAP Powering Off the Tape Library Powering On the Tape LibraryOpening the Front Door Without Power Manual ModeDoor Locking Lever Extended Securing the Front Door Without PowerInsert Cartridges Into Slots Locate and Remove CartridgeInserting Cartridges Into Slots Inserting Cartridge Into Tape Drive Inserting a Cartridge Into a Tape DriveLocation of Unload Button Removing a Cartridge From a Tape DriveRemoving a Cartridge From the Gripper Assembly Manual Release Screw Replacing a Cleaning CartridgePage Inspect Cartridges Cartridge InformationHandle Cartridges Maintain Cartridges Valid Labels Ultrium CartridgesApply Cartridge Labels Label Type of Cartridge LTO Cartridge CodesUltrium Cartridge Label Write-Protect Switch Setting the Write-Protect SwitchSpecification L3 Cartridge L2 Cartridge L1 Cartridge LTO Gen 1, Gen 2, and Gen 3 Cartridge SpecificationsPage ServerNet/DA Supported ConnectionsAdding the Control Path and the Data Path To add the data path PMF CRU PMF CRU Adding the Control Path and Data Path Supported ConnectionTo add the data path SCF, issue this command Configuration Overview Series Rear View System Configuration Example Fiber-opticAdding the Control Path and Data Path Page Figure A-1. Library and Rack Dimensions SpecificationsFigure A-2. Tape Library and Rack Dimensions Table A-1. Library Component Weights Tape Library Components WeightsTable A-2. Library Environment Specifications Tape Library EnvironmentPower Cord Numbers and Receptacles PowerTable A-3. Power Cord and Receptacles Table A-4. Non-Country-Specific CordsInstalling the Power Cords Figure A-3. Power Cabling Table A-6. Power for Base Unit and Two LTO Tape Drives Power SpecificationsTable A-5. Power for Library Without Tape Drives Page Regulatory Compliance Statements Safety and ComplianceFCC Compliance Canadian ComplianceStatements-2 Laser Compliance European Union NoticeSafety Caution High Leakage Current Waste Electrical and Electronic Equipment WeeeSafety