HP SL500 (M852x) manual Sliding a Magazine Into a CAP

Page 34

Library Operation

Entering a Cartridge Through the CAP

4.Place the cartridge into one of the magazine slots, making sure that the VOLID label is visible and the hub of the cartridge is down.

5.Grip the handle and slide the magazine back into the CAP.

Figure 3-1. Sliding a Magazine Into a CAP

6. Close the CAP door making sure that the door is securely latched.

SL500 (M852x) Tape Library Installation and User’s Guide—541531-006

3-2

Image 34

Contents Abstract Product Version Supported Release Version Updates RVUsPart Number Published Document History Part Number Product Version Published SL500 M852x Tape Library Installation and User’s Guide Overview of the Tape LibraryCartridge Information Figures TablesContents New and Changed Information What’s New in This ManualManual Information Document HistoryPage Hypertext Links About This ManualNotation Conventions Change Bar NotationViii Overview of the Tape Library This section includesViews and Locations Front View of Tape Library ComponentsBack View of Tape Library Components Physical Configurations Base Module Slots Slots Locations for Firmware Slot Mapping Slots Locations for Scsi Element Numbering Mapping Slot Capacity for Back Wall of Cartridge Expansion Module Capacities CAP Robotics Unit Robotics Components Hand Assembly RLC Card ElectronicsFans Interface CardsCartridge Access Port Power SystemCAP Condition Supported Tape Drives LTO Generation 3 SpecificationsSpecification Performance LTO UltriumAudit of Tape Library Safety FeaturesCards and Power Supply RoboticsInterfaces 10. Tape Library Interfaces LocationsPower Switch Controls and IndicatorsKeypad Buttons and Indicators Indicator Keypad Buttons and IndicatorsButtons/Indicators Description ButtonPage Securing the Front Door With Power Automated ModeOpening the Front Door With Power Library OperationSliding a Magazine Into a CAP Powering On the Tape Library Powering Off the Tape LibraryManual Mode Opening the Front Door Without PowerSecuring the Front Door Without Power Door Locking Lever ExtendedLocate and Remove Cartridge Insert Cartridges Into SlotsInserting Cartridges Into Slots Inserting a Cartridge Into a Tape Drive Inserting Cartridge Into Tape DriveRemoving a Cartridge From a Tape Drive Location of Unload ButtonRemoving a Cartridge From the Gripper Assembly Replacing a Cleaning Cartridge Manual Release ScrewPage Handle Cartridges Cartridge InformationInspect Cartridges Maintain Cartridges Apply Cartridge Labels Ultrium CartridgesValid Labels LTO Cartridge Codes Label Type of CartridgeUltrium Cartridge Label Setting the Write-Protect Switch Write-Protect SwitchLTO Gen 1, Gen 2, and Gen 3 Cartridge Specifications Specification L3 Cartridge L2 Cartridge L1 CartridgePage Adding the Control Path and the Data Path Supported ConnectionsServerNet/DA To add the data path PMF CRU PMF CRU Supported Connection Adding the Control Path and Data PathTo add the data path SCF, issue this command Configuration Overview Configuration Example Fiber-optic Series Rear View SystemAdding the Control Path and Data Path Page Specifications Figure A-1. Library and Rack DimensionsFigure A-2. Tape Library and Rack Dimensions Table A-2. Library Environment Specifications Tape Library Components WeightsTable A-1. Library Component Weights Tape Library EnvironmentTable A-3. Power Cord and Receptacles PowerPower Cord Numbers and Receptacles Table A-4. Non-Country-Specific CordsInstalling the Power Cords Figure A-3. Power Cabling Table A-5. Power for Library Without Tape Drives Power SpecificationsTable A-6. Power for Base Unit and Two LTO Tape Drives Page FCC Compliance Safety and ComplianceRegulatory Compliance Statements Canadian ComplianceStatements-2 European Union Notice Laser ComplianceSafety Caution Waste Electrical and Electronic Equipment Weee High Leakage CurrentSafety