HP SL500 (M852x) manual Cap

Page 20

Overview of the Tape Library								Capacities

	Table 1-1. Cartridge Slot and Tape Drive Capacities
	Modules	Maximum Number of Tape Drives					CAP	Total
							Slots	Number of
								Slots
		2	6	10	14	18
	Base Module	30					5	35
	20 cartridge upgrade key	50					5	55
	Adding one expansion module
	Base module plus 1		100				15	115
	limited DEM
	Base module plus 1		143				15	158
	DEM
	Base module plus 1	170					15	185
	CEM
	Adding two expansion modules
	Base module plus 2			227			25	252
	limited DEMs
	Base module plus 1		254				25	279
	DEM, 1 CEM
	Base module plus 2	290					25	315
	CEMs
	Adding three expansion modules
	Base module plus 3				311		35	346
	DEMs
	Base module plus 2			338			35	373
	DEMs, 1 CEM
	Base module plus 1		374				35	409
	DEM, 2 CEMs
	Base module plus 3	410					35	445
	CEMs
	Adding four expansion modules
	Base module plus 4					395	45	440
	DEMs
	Base module plus 3				422		45	467
	DEMs, 1 CEM
	Base module plus 2			458			45	503
	DEMs, 2 CEMs
	Base module plus 1		494				45	539
	DEM, 3 CEMs
	Base module plus 4	530					45	575
	CEMs

SL500 (M852x) Tape Library Installation and User’s Guide—541531-006

1-10

Image 20

Contents Part Number Published Product Version Supported Release Version Updates RVUsAbstract Document History Part Number Product Version Published SL500 M852x Tape Library Installation and User’s Guide Overview of the Tape LibraryCartridge Information Figures TablesContents What’s New in This Manual Manual InformationNew and Changed Information Document HistoryPage About This Manual Notation ConventionsHypertext Links Change Bar NotationViii Overview of the Tape Library This section includesViews and Locations Front View of Tape Library ComponentsBack View of Tape Library Components Physical Configurations Base Module Slots Slots Locations for Firmware Slot Mapping Slots Locations for Scsi Element Numbering Mapping Slot Capacity for Back Wall of Cartridge Expansion Module Capacities CAP Robotics Unit Robotics Components Hand Assembly Electronics FansRLC Card Interface CardsCAP Condition Power SystemCartridge Access Port LTO Generation 3 Specifications Specification PerformanceSupported Tape Drives LTO UltriumSafety Features Cards and Power SupplyAudit of Tape Library RoboticsInterfaces 10. Tape Library Interfaces LocationsKeypad Controls and IndicatorsPower Switch Buttons and Indicators Keypad Buttons and Indicators Buttons/Indicators DescriptionIndicator ButtonPage Automated Mode Opening the Front Door With PowerSecuring the Front Door With Power Library OperationSliding a Magazine Into a CAP Powering On the Tape Library Powering Off the Tape LibraryManual Mode Opening the Front Door Without PowerSecuring the Front Door Without Power Door Locking Lever ExtendedLocate and Remove Cartridge Insert Cartridges Into SlotsInserting Cartridges Into Slots Inserting a Cartridge Into a Tape Drive Inserting Cartridge Into Tape DriveRemoving a Cartridge From a Tape Drive Location of Unload ButtonRemoving a Cartridge From the Gripper Assembly Replacing a Cleaning Cartridge Manual Release ScrewPage Inspect Cartridges Cartridge InformationHandle Cartridges Maintain Cartridges Valid Labels Ultrium CartridgesApply Cartridge Labels LTO Cartridge Codes Label Type of CartridgeUltrium Cartridge Label Setting the Write-Protect Switch Write-Protect SwitchLTO Gen 1, Gen 2, and Gen 3 Cartridge Specifications Specification L3 Cartridge L2 Cartridge L1 CartridgePage ServerNet/DA Supported ConnectionsAdding the Control Path and the Data Path To add the data path PMF CRU PMF CRU Supported Connection Adding the Control Path and Data PathTo add the data path SCF, issue this command Configuration Overview Configuration Example Fiber-optic Series Rear View SystemAdding the Control Path and Data Path Page Specifications Figure A-1. Library and Rack DimensionsFigure A-2. Tape Library and Rack Dimensions Tape Library Components Weights Table A-1. Library Component WeightsTable A-2. Library Environment Specifications Tape Library EnvironmentPower Power Cord Numbers and ReceptaclesTable A-3. Power Cord and Receptacles Table A-4. Non-Country-Specific CordsInstalling the Power Cords Figure A-3. Power Cabling Table A-6. Power for Base Unit and Two LTO Tape Drives Power SpecificationsTable A-5. Power for Library Without Tape Drives Page Safety and Compliance Regulatory Compliance StatementsFCC Compliance Canadian ComplianceStatements-2 European Union Notice Laser ComplianceSafety Caution Waste Electrical and Electronic Equipment Weee High Leakage CurrentSafety