HP Latex 260 61-in Japan ( L26500 61-in Japan ) manual Handle the substrate

Page 47

8.Ensure that both stops are placed on the spindle, but leave some space between the core and the stops at each end.

9.Load the take-up reel spindle into the printer by pushing firmly on both ends of the spindle.

10.Press the OK button on the front panel.

Advance the substrate using the arrows on the front panel. Make sure that the substrate passes in front of the loading table, as shown.

11.Pull down the center of the substrate's leading edge to straighten the substrate. Do not attempt to pull more substrate out of the printer.

NOTE: If you are loading the take-up reel during printing you do not need to pull the substrate taut. Tape the substrate to the spindle core when an adequate length of substrate has fed from the printer after printing begins.

12.Adjust the position of the core on the take-up reel spindle so that it is aligned with the substrate.

Handle the substrate

ENWW	The take-up reel 43

Image 47

Contents Designjet L26500 / L26100 printer series Trademarks Legal noticesTable of contents Ink system Electrical shock hazard Safety precautionsGeneral safety guidelines IntroductionFire hazard Heat hazardInk handling Mechanical hazardHeavy substrate hazard Introduction Printer’s main components Printer’s main featuresFront view Edge holders case Rear viewDrying enclosure Take-up reel motor Front panel Loading accessoryEmbedded Web Server Support tab Setup tabTurn the printer on and off Main tabRestart the printer Connection type Speed Maximum cable length Other factors Connectivity and software instructionsConnection method Connect to a networkConnectivity View or set the date and time Basic setup optionsPrinter setup options Change the language of the front panelTurn the buzzer on or off Request e-mail notification of specific error conditionsChange the cool-down delay Change the sleep mode settingChange the language of the Embedded Web Server Embedded Web Server setup optionsRestore factory settings Access the Embedded Web ServerRestrict access to the printer Substrate tips Handle the substrateOverview Substrate family Description Example HP Heavyweight Coated PaperSupported substrate families Supported HP substrates Specialty materials Back ProLoad a roll onto the spindle Porous substratesLift the spindle lock lever to disengage the spindle Load a roll onto the spindle Handle the substrate Load a roll into the printer automatically Handle the substrate Handle the substrate Load a roll into the printer manually Load a roll into the printer manually Select the type of substrate you are loading Unload a roll from the printer Load a cut sheet into the printerLoop-shapers Take-up reelTake-up reel Handle the substrate Handle the substrate Handle the substrate Handle the substrate Handle the substrate Load a roll onto the take-up reel other substrates Handle the substrate Handle the substrate Handle the substrate Handle the substrate Handle the substrate Unload a roll from the take-up reel Handle the substrate Edge holders Loading accessory Loading accessory Handle the substrate Handle the substrate Outline Double-sided printingDouble-sided printing View information about the substrate Substrate length tracking Store the substrate Enable/disable the length tracking featureAdd a new substrate Substrate settingsDownload media presets Summary Select printer settings and color profile Airflow Tracking Setting Description If too low If too highSubstrate family Drying Curing Heating Auto Substrat Input Vacuum TempSubstrates in normal Omas Load the substrate and print the diagnostic plotAdvanced settings Change settings while printingLow-temp Mesh Aqueou Temperature profileSelect the number of passes Key Check the quantity of ink on the substrateSubstrate settings Substrate settings Color calibration Faster printingColor reproduction tricks Color profilesSubstrate settings Retrieving usage information Request accounting data by E-mail Get accounting informationCheck usage statistics Check usage statistics for a jobSet Send accounting files to Enabled Printheads Ink systemInk system components Ink cartridgesPrinthead cleaning cartridge Printhead cleaning kitInk funnel Printhead cleaning containerInk maintenance kit Kit Part number Order ink suppliesCartridge Capacity ml Part number Printhead Part numberChange margins Print optionsPrinter states Request the printer’s internal prints Name Product number AccessoriesOrder accessories Minimum Maximum Printer specificationsFunctional specifications Outside Japan Japan only Physical specificationsMemory specifications Power specificationsAcoustic specifications Environmental specificationsBack tension GlossaryPET PVC Index Safety labels