HP Latex 260 61-in Japan ( L26500 61-in Japan ) manual Handle the substrate

Page 57

9.Select the type of substrate you are loading.

NOTE: You should select the name of the particular substrate that you are using in your RIP software, not in the front panel.

TIP: When loading very thin substrates, always select the substrate type as Banner to minimize the vacuum pressure applied while loading; when loading very thick substrates, always select the substrate type as HP Photorealistic to maximize the vacuum pressure. After loading and before printing, go to the front panel and change to the correct type for the substrate you are loading: select the icon, then select View loaded substrate > Change loaded substrate.

10.After passing through the printer, the loading accessory can be removed by hand.

11.The printer checks the substrate in various ways and may ask you to correct problems with skew or tension.

NOTE: You can specify the maximum permitted amount of skew at the front panel: select the icon, then select Substrate handling options > Max skew setting.

12.If you are loading transparent substrate without opaque borders, you are asked to enter the width of the substrate and the distance of the right edge from the printer's side plate (as indicated by the ruler on the front of the curing module).

13.If you have chosen double-sided printing, the front panel may ask a question about it at this point.

14.The printer calibrates the substrate advance.

Handle the substrate

ENWW	The loading accessory 53

Image 57

Contents Designjet L26500 / L26100 printer series Trademarks Legal noticesTable of contents Ink system General safety guidelines Safety precautionsIntroduction Electrical shock hazardFire hazard Heat hazardMechanical hazard Heavy substrate hazardInk handling Introduction Printer’s main components Printer’s main featuresFront view Edge holders case Rear viewDrying enclosure Take-up reel motor Front panel Loading accessoryEmbedded Web Server Turn the printer on and off Setup tabMain tab Support tabRestart the printer Connection method Connectivity and software instructionsConnect to a network Connection type Speed Maximum cable length Other factorsConnectivity Printer setup options Basic setup optionsChange the language of the front panel View or set the date and timeChange the cool-down delay Request e-mail notification of specific error conditionsChange the sleep mode setting Turn the buzzer on or offRestore factory settings Embedded Web Server setup optionsAccess the Embedded Web Server Change the language of the Embedded Web ServerRestrict access to the printer Handle the substrate OverviewSubstrate tips Example HP Heavyweight Coated Paper Supported substrate familiesSubstrate family Description Supported HP substrates Specialty materials Back ProLoad a roll onto the spindle Porous substratesLift the spindle lock lever to disengage the spindle Load a roll onto the spindle Handle the substrate Load a roll into the printer automatically Handle the substrate Handle the substrate Load a roll into the printer manually Load a roll into the printer manually Select the type of substrate you are loading Unload a roll from the printer Load a cut sheet into the printerLoop-shapers Take-up reelTake-up reel Handle the substrate Handle the substrate Handle the substrate Handle the substrate Handle the substrate Load a roll onto the take-up reel other substrates Handle the substrate Handle the substrate Handle the substrate Handle the substrate Handle the substrate Unload a roll from the take-up reel Handle the substrate Edge holders Loading accessory Loading accessory Handle the substrate Handle the substrate Outline Double-sided printingDouble-sided printing View information about the substrate Substrate length tracking Store the substrate Enable/disable the length tracking featureSubstrate settings Download media presetsAdd a new substrate Summary Select printer settings and color profile Substrate family Drying Curing Heating Auto Setting Description If too low If too highSubstrat Input Vacuum Temp Airflow TrackingSubstrates in normal Omas Load the substrate and print the diagnostic plotAdvanced settings Change settings while printingLow-temp Mesh Temperature profile Select the number of passesAqueou Key Check the quantity of ink on the substrateSubstrate settings Substrate settings Color calibration Faster printingColor reproduction tricks Color profilesSubstrate settings Retrieving usage information Check usage statistics Get accounting informationCheck usage statistics for a job Request accounting data by E-mailSet Send accounting files to Enabled Ink system components Ink systemInk cartridges PrintheadsPrinthead cleaning cartridge Printhead cleaning kitInk funnel Printhead cleaning containerInk maintenance kit Cartridge Capacity ml Part number Order ink suppliesPrinthead Part number Kit Part numberPrint options Printer statesChange margins Request the printer’s internal prints Accessories Order accessoriesName Product number Printer specifications Functional specificationsMinimum Maximum Memory specifications Physical specificationsPower specifications Outside Japan Japan onlyAcoustic specifications Environmental specificationsBack tension GlossaryPET PVC Index Safety labels