HP Latex 260 61-in Japan ( L26500 61-in Japan ) Physical specifications, Memory specifications

Page 89

Table 10-4 Margins

Side margins	5 mm (0.2 in)

Top margin (leading edge)	5 mm (0.2 in)

Bottom margin (trailing edge)	5 mm (0.2 in) (none)
	100 mm (3.9 in) (small)
	150 mm (5.9 in) (normal)
	200 mm (7.9 in) (extra)
	300 mm (11.8 in) (extra)
	400 mm (15.7 in) (extra)
	500 mm (19.7 in) (extra)

Physical specifications

Table 10-5Printer physical specifications

Weight (including stand)	L26500 - 202kg / L26100 - 180kg

Width	2465 mm

Depth	690 mm

Height	1370 mm

Memory specifications

Table 10-6Memory specifications

Memory (DRAM)	512	MB

Hard disk	160	GB

Power specifications

NOTE: An electrician is required for the setup and configuration of the building electrical system used to power the printer and also for printer installation. Make sure that your electrician is appropriately certified according to local regulations and supplied with all the information regarding the electrical configuration.

Your printer requires that the following electrical components be supplied and installed by the customer, according to the National Electrotechnical Code (NEC).

Table 10-7Single phase line specifications

	Outside Japan	Japan only

Number of power cords	2	2

Printer specifications

ENWW	Physical specifications 85

Image 89

Contents Designjet L26500 / L26100 printer series Trademarks Legal noticesTable of contents Ink system General safety guidelines Safety precautionsIntroduction Electrical shock hazardFire hazard Heat hazardInk handling Mechanical hazardHeavy substrate hazard Introduction Printer’s main components Printer’s main featuresFront view Edge holders case Rear viewDrying enclosure Take-up reel motor Front panel Loading accessoryEmbedded Web Server Turn the printer on and off Setup tabMain tab Support tabRestart the printer Connection method Connectivity and software instructionsConnect to a network Connection type Speed Maximum cable length Other factorsConnectivity Printer setup options Basic setup optionsChange the language of the front panel View or set the date and timeChange the cool-down delay Request e-mail notification of specific error conditionsChange the sleep mode setting Turn the buzzer on or offRestore factory settings Embedded Web Server setup optionsAccess the Embedded Web Server Change the language of the Embedded Web ServerRestrict access to the printer Substrate tips Handle the substrateOverview Substrate family Description Example HP Heavyweight Coated PaperSupported substrate families Supported HP substrates Specialty materials Back ProLoad a roll onto the spindle Porous substratesLift the spindle lock lever to disengage the spindle Load a roll onto the spindle Handle the substrate Load a roll into the printer automatically Handle the substrate Handle the substrate Load a roll into the printer manually Load a roll into the printer manually Select the type of substrate you are loading Unload a roll from the printer Load a cut sheet into the printerLoop-shapers Take-up reelTake-up reel Handle the substrate Handle the substrate Handle the substrate Handle the substrate Handle the substrate Load a roll onto the take-up reel other substrates Handle the substrate Handle the substrate Handle the substrate Handle the substrate Handle the substrate Unload a roll from the take-up reel Handle the substrate Edge holders Loading accessory Loading accessory Handle the substrate Handle the substrate Outline Double-sided printingDouble-sided printing View information about the substrate Substrate length tracking Store the substrate Enable/disable the length tracking featureAdd a new substrate Substrate settingsDownload media presets Summary Select printer settings and color profile Substrate family Drying Curing Heating Auto Setting Description If too low If too highSubstrat Input Vacuum Temp Airflow TrackingSubstrates in normal Omas Load the substrate and print the diagnostic plotAdvanced settings Change settings while printingLow-temp Mesh Aqueou Temperature profileSelect the number of passes Key Check the quantity of ink on the substrateSubstrate settings Substrate settings Color calibration Faster printingColor reproduction tricks Color profilesSubstrate settings Retrieving usage information Check usage statistics Get accounting informationCheck usage statistics for a job Request accounting data by E-mailSet Send accounting files to Enabled Ink system components Ink systemInk cartridges PrintheadsPrinthead cleaning cartridge Printhead cleaning kitInk funnel Printhead cleaning containerInk maintenance kit Cartridge Capacity ml Part number Order ink suppliesPrinthead Part number Kit Part numberChange margins Print optionsPrinter states Request the printer’s internal prints Name Product number AccessoriesOrder accessories Minimum Maximum Printer specificationsFunctional specifications Memory specifications Physical specificationsPower specifications Outside Japan Japan onlyAcoustic specifications Environmental specificationsBack tension GlossaryPET PVC Index Safety labels