Electrical Specifications | Xantrex Technology PH1800 manual

Specifications

Electrical Specifications

Table A-1Electrical Specifications for the Inverter

Parameter	PowerHub 1800 Inverter

Maximum Output Power	1800 W (15A) (5 minutes maximum)

Continuous Output Power	1440 W (12 A)

Surge Rating	2880 W (24 A)

Input Voltage Range	10.5 to 15.0 Vdc

Input Frequency Range	60 Hz

Peak Efficiency	88%

System Shutdown Mode	< 12 W
(Display On)

Idle Mode	<1.5 W

Output Frequency	60 Hz / ±1 Hz

Output Waveform (resistive load)	Modified sine wave (>30% THD)

Output Voltage (at no load)	110 to 125 Vac

Low Battery Cutout	10.5 Vdc with < 240 W load and 11.0 V with > 240 W load

High Battery Cutout	15.0 Vdc

Transfer Relay Rating	20 A

Transfer Time AC to Inverter	< 40 ms

AC Qualification Time	~ 20 seconds

Protection	• Five 20 A/32 Vdc fuses protecting the 80A/1000 W DC input
	terminal.
	• Two 20 A/32 Vdc fuses protecting 32A/ 400 W DC input
	terminal.
	• One 15 Aac supplemental protector.
	• One 1 A/250 Vac fuse for system ground fault protection.

Table A-2Electrical Specifications for the Battery Box

Parameter

Protection

Battery Box1

Ten 20 A/32 Vdc Fuses for short circuit and reverse polarity conditions.

1.Stand-alone battery box Xantrex Part Number: PH1800-BBX

A–2	975-0288-01-01

Image 50

Xantrex Technology PH1800 manual Table A-1Electrical Specifications for the Inverter

Contents

PowerHub Page PowerHub Operator’s Guide Date and Revision Scope About This GuidePurpose Audience Related Information Conventions UsedAbbreviations and Acronyms Important Safety Instructions Figure i Basic Safety Precautions When Working With Batteries Precautions for Using Rechargeable Appliances FCC/ICES 003 Information to the User Power Down Procedure To Power Down the PowerHub If hardwired...... To Power Down the PowerHub Contents Troubleshooting Specifications Figures Xiv Tables Page Introduction For this topic See Introduction Principles of Inverter Operation Basic Functions of the PowerHub Primary AC source Inverter Features 2PowerHub 1800 Features Battery Charger Features Three-Stage Charging Process on Voltage 12.5 Vdc Contains information on operating the PowerHub Operation 8.8 Inverter Control Panel User Controls and Display LED Operating Mode LEDs Status LEDs Selecting Charger Settings AC LED Power On and Off Basic Operation Changing the Display 3Input Displays 4Output Displays Changing Charging Settings AC is not available Connecting AC Loads 6Connecting AC Loads Loads that should not be used with the PowerHub Typical Loads that might be used with the PowerHubLoads That Might Not Work Well With the PowerHub Troubleshooting How to Troubleshoot the PowerHub Error Codes Troubleshooting Error Codes for Troubleshooting the PowerHub If Utility Power is not Available 2Possible Problems if Utility Power is Not Available Error code E02 If Utility Power is Available 3Possible Problems if Utility Power is Available Possible Problem Loads Rechargeable Devices Ground Fault Protection Replacing the Ground Fault Protection Fuse 1Replacing Ground Fault Protection Fuse Page Specifications Electrical Specifications Table A-1Electrical Specifications for the Inverter Physical Specifications Battery Charger Specifications Figure A-1Three-Stage Charging Process Charging Profiles Amp Charging Profile Table A-610-amp Charging Profile Index IX-2 975-0288-01-01 Warranty and Return Information Warranty Disclaimer Product Exclusions Return Material Authorization PolicyReturn Procedure Out of Warranty Service Information About Your System Purchased From Purchase Date WA-6 Page Xantrex Technology Inc