Manuals / Xantrex Technology / Computer Equipment / Switch

Xantrex Technology PH1800 manual Displayed, of Error, Description of Condition, Resolution

Models: PH1800

1 64

Download 64 pages 61.71 Kb

Page 40

Manual background

Troubleshooting

Table 3-1	Error Codes for Troubleshooting the PowerHub 1800
Error Code		Description
Error Code		Description
Displayed		of Error	Description of Condition		Resolution

E06		AC Output	System is still operating but AC load		Unit continues to run.
		Overload	applied to the system in inverter mode is		If the warning is ignored, the
		Warning	close to shutdown limit.		unit will eventually go to the
			Alarm will beep once every two seconds		E03 fault condition.
			Alarm will beep once every two seconds
			until the warning condition is removed.

E07		System Over	System is still operating but system		Unit continues to run.
		Temperature	internal temperature is close to shutdown		If the warning is ignored, unit
		Warning	limit.		will eventually go to the E04
			Alarm will beep once every two seconds		fault condition.
			Alarm will beep once every two seconds
			until the warning condition is removed.

E09		Ground Fault	Unit shuts down.		Turn the unit off. Check all DC
		Fuse Open	A ground fault has been detection.		Input connections (PV, wind
		Warning	A ground fault has been detection.		etc.) and repair any faults or
		Warning			etc.) and repair any faults or
					damage. Replace the ground
					fault fuse (see page 3–10) and
					restart the unit

3–4	975-0288-01-01

Image 40

Xantrex Technology PH1800 manual Displayed, of Error, Description of Condition, Resolution

Contents

Operator’s Guide PowerHubPH1800 Page Operator’s Guide PowerHubAbout Xantrex TrademarksNotice of Copyright Exclusion for DocumentationAbout This Guide PurposeScope AudienceConventions Used Abbreviations and AcronymsRelated Information The following conventions are used in this guideImportant Safety Instructions WARNING Limitations on useFigure i Basic Safety No NoNo No Precautions When Working With Batteries WARNING Fire or Explosion HazardFCC/ICES 003 Information to the User Precautions for Using Rechargeable AppliancesCAUTION Equipment Damage Power Down Procedure To Power Down the PowerHubWARNING Shock Hazard If hardwired...... To Power Down the PowerHubFigure iii Power Down Procedure for Hardwired Installations Safety1 Introduction Contents2 Operation 3 Troubleshooting A SpecificationsFigures Page Tables Page 1 Introduction For this topicIntroduction Principles of Inverter Operationwill illuminate if AC power is available at the AC outlets Basic Functions of the PowerHubWARNING Shock Hazard User Features Inverter FeaturesWARNING Shock Hazard Battery Charger Features Standby Mode Voltage 12.5 VdcCurrent CurrentChapter 2 contains information on operating the PowerHub 2 OperationFor this topic Figure 2-1 The PowerHub 1800 Inverter Control Panel Inverter Control Panel8.8.8.8 WARNING Shock Hazard User Controls and DisplayThe following provides a detailed description of the user controls and Operating Mode LEDs Status LEDsInput LEDs WARNING Shock HazardSelecting Charger Settings Output LEDsBasic Operation Power On and OffTo turn the power to the PowerHub ON or OFF Changing the Display Figure 2-3 Input DisplaysBasic Operation 975-0288-01-01Net Power will be displayed Battery Voltage will be displayed Figure 2-4 Output DisplaysOperation 975-0288-01-01Changing Charging Settings Connecting AC Loads CAUTION Equipment DamageFigure 2-6 Connecting AC Loads Connecting AC LoadsON/OFF Power Button 120 Vac Power Outlets x4 AC Indicator LED WARNING Shock HazardLoads That Might Not Work Well With the PowerHub Typical Loads that might be used with the PowerHubLoads that should NOT be used with the PowerHub 3 Troubleshooting For this topicHow to Troubleshoot the PowerHub Error Codes of ErrorResolution Descriptionof Error ResolutionDescription DisplayedIf Utility Power is NOT Available Table 3-2 Possible Problems if Utility Power is Not AvailableProblem SolutionTable 3-2 Possible Problems if Utility Power is Not Available ProblemSolution battery. Check battery is not overchargedIf Utility Power is Available Table 3-3 Possible Problems if Utility Power is AvailableProblem SolutionPossible Problem Loads WARNING Fire HazardRechargeable Devices CAUTION Equipment Damage Ground Fault Protection Replacing the Ground Fault Protection FuseWARNING Shock hazard WARNING Energy and fire hazardFigure 3-1 Replacing Ground Fault Protection Fuse Ground Fault Protectionpanel to expose the terminals PV Ground Fault Protection Fuse AC Indicator LED3-12 A Specifications Electrical Specifications Table A-1 Electrical Specifications for the InverterTable A-2 Electrical Specifications for the Battery Box PowerHub 1800 InverterPhysical Specifications Battery Charger SpecificationsTable A-3 Physical Specifications of the Inverter Table A-4 Physical Specifications of the Battery BoxVoltage 12.5 Vdc CurrentCurrent Figure A-1 Three-Stage Charging ProcessCharging Profiles 40-amp Charging ProfileDefault Value Table A-5 40-amp Charging Profile0-amp Charging Profile 10-amp Charging ProfileTable A-6 10-amp Charging Profile Index warranty out of warranty service WA-4 terms and conditions WA-1 IndexRechargeable Devices Wind LEDWarranty and Return Information WarrantyDisclaimer ProductReturn Procedure Return Material Authorization PolicyExclusions Out of Warranty Service Information About Your System WA-6 Page Xantrex Technology Inc 1 800 670 0707 Tel toll free NA 1 360 925 5097 Tel direct1 800 994 7828 Fax toll free NA 975-0288-01-01