Fender PDP-125, PDP-S50 manual E t u p, Configuration

Page 12

12 S e t - u p

Configuration 1:

The Passive PDP Speakers can be used with up to 40 watts average power / 80 watts peak power amplifiers. Often, this amplifier will be built into the Plasma Display Panel unit.

Configuration 3:

The Powered PDP Speakers are composed of one powered speaker, and a slave speaker which is identical to the Passive PDP Speakers. The Powered PDP Speaker can connect to the audio output of the PDP Monitor, using either a 3.5mm stereo phone plug or RCA connectors. The slave PDP speaker is connected to the Powered PDP Speaker's output connector.

Configuration 2:

When a PDP Subwoofer is added to the Passive PDP Speakers, the PDP Subwoofer can be connected to the Speaker Level Outputs from the PDP monitor. The PDP Subwoofer will pass the signal through a High-Pass Crossover Filter. The Passive PDP Speakers are connected to the High-Pass Crossover via the Speaker Level High-Frequency Outputs on the PDP Subwoofer.

Configuration 4:

When a PDP Subwoofer is added to the Powered PDP Speaker system, it is connected to the audio output of the PDP Monitor, using either a 3.5mm stereo phone plug or RCA connectors. The Powered PDP Speaker is then connected to the 3.5 mm High-Frequency Output Jack of the PDP Subwoofer. The slave speaker is connected to the Powered PDP Speaker's amplifier output.

✧ f e n d e r . c o m ✧

Page 11 Page 13
Image 12
Page 11 Page 13
Contents PDP Speaker System 34-37 General Precautions P o r t a n t S a f e t y I n s t r u c t i o n sPrecauciones generales N s i g n e s d e S é c u r i t é I m p o r t a n t e s Précautions généralesPrecauzioni generali C h t i g e S i c h e r h e i t s v o r k e h r u n g e n Allgemeine SicherheitsvorkehrungenS t r u ç õ e s I m p o r t a n t e s d e S e g u r a n ç a Precauções GeraisN d e r . c o m PDP-125 Powered Presentation Loudspeakers D P S p e a k e r S y s t e m sPDP-1 Passive Presentation Loudspeakers P 1 P 1 2P S 5 Configuration E t u pPower Requirements Power OutputDimensions ModelI s t e m a s d e a l t a v o c e s P D P Recintos pasivos para presentaciones PDP-1Recintos autoamplificados para presentaciones PDP-125 Conector DE Corriente IEC Conecte el cable de alimentación a Configuración O n f i g u r a c i ó nP e c i f i c a c i o n e s t é n i c a s Y s t è m e s d ’ e n c e i n t e s P D P Enceintes passives PDP-1Enceintes actives PDP-125 Subwoofer PDP-S50P 1 O n f i g u r a t i o n R a c t é r i s t i q u e s t e c h n i q u e s PDP-1 Diffusori Passivi PDP-125 Diffusori AttiviP 1 Configurazione E c i f i c h e D P B o x e n s y s t e m e PDP-1 Passive PräsentationsboxenPDP-125 Aktive Präsentationsboxen Speaker Level Input Diese IEC NETZKABEL-ANSCHLUSSKonfiguration Te c h n i s c h e D a t e n S t e m a d e a l t o f a l a n t e s P D P PDP-1 Alto-falantes Passivos de PresentaçãoPDP-125 Alto-falantes de Potência de Presentação IEC Line Cord Connector O cabo de alimentação deve ser Configuração O n f i g u r a ç ã oPeças Numeros Potência RequeridaPotência Potência DE SaídaN d e r . c o m N d e r . c o m N d e r . c o m N d e r . c o m
Top Page Image Contents