HP E1367A, E1366A manual Comments ∙ RF Multiplexers Model Number

Page 55

Parameters

Parameter Name	Parameter Type	Range of Values

<number>	numeric	1-99

Comments ∙ RF Multiplexers Model Number:

The SYSTem:CTYPe? <number> command returns

"HEWLETT-PACKARD,E1366A,0,A.01.00"(E1366A), or returns "HEWLETT-PACKARD,E1367A,0,A.01.00"(E1367A), where the "0" after "E1366A" or "E1367A" is the module serial number (always 0) and "A.01.00" is an example of the module revision code number.

Example Reading the Model Number of a Card #1 Module

SYST:CTYP? 1

! Return the model number

:CPON SYSTem:CPON <number> ALL sets the selected module (card) in a switchbox to its power-on state.

Parameters

	Parameter Name	Parameter Type		Range of Values

	<number>	numeric		1-99

Comments	∙ RF Multiplexers Power-On State: The power-on state is all
	channels (relays) open. Note that *RST opens all channels of all
	modules in a switchbox, while SYSTem:CPON opens the channels
	in only the module (card) specified in the command.
Example Setting Card #1 Module to its Power-on State
	SYST:CPON 1		! Sets module #1 to power-on state

Chapter 5

HP E1366A/E1367A RF Multiplexers Command Reference 55

Image 55

Contents Contents HP E1366A/E1367A RF Multiplexers Command Reference HP E1366A/E1367A RF Multiplexer Specifications HP E1366A/67A RF Multiplexers User’s Manual Contents HP E1366A & E1367A RF Multiplexer Modules User’s Manual Documentation History According to ISO/IEC Guide 22 and EN December 5HP E1366A & E1367A RF Multiplexer Modules User’s Manual Reader Comment Sheet Measurement Systems DivisionHP E1366A & E1367A RF Multiplexer Module User’s Manual Getting Started with the HP E1366A/E1367A RF Multiplexers Using This ChapterMultiplexer Module Description Multiplexers Switching Diagram Address Typical ConfigurationSpecifying Scpi Commands Programming the Multiplexer ModuleMultiplexer Channel Numbers Multiplexer Card NumbersExample RF Multiplexer Channel Lists/Ranges Initial OperationPage Chapter Configuring the HP E1366A/E1367A RF Multiplexers Configuring the HP E1366A/E1367A RF MultiplexersConfiguring the HP E1366A/E1367A RF Multiplexers Chapter Connecting User InputsHewlett-Packard BNC Cables Standard Configuration Typical Multiplexer ConfigurationsTypical Tree Configuration Typical Matrix-Type Configuration Matrix-Type ConfigurationRF Multiplexer Component Locations Changing Multiplexer ComponentsConfiguring the HP E1366A/E1367A RF Multiplexers Chapter Chapter Using the HP E1366A/E1367A RF Multiplexer Module Using the HP E1366A/E1367A RF Multiplexer ModuleMultiplexer Commands Switching ChannelsUsing the HP E1366A/E1367A RF Multiplexer Module Chapter Example Standard SwitchingTree Switching Example Tree SwitchingQuery Channel States. Use CLOSe? channellist or Example Matrix-Type SwitchingScanning Channels Example Scanning Using Trig Out PortScanning Channels Comments Scanning with External Instruments Scanning Channels CommandsUsing Scanning Trigger Sources Understanding the HP E1366A/E1367A RF MultiplexersUnderstanding the HP E1366A/E1367A RF Multiplexers Chapter Scanning Trigger Sources Scanning with External Device Example Scanning with External DeviceExample Scanning Using Trig Out Event Ports Example Scan Complete Interrupt Using the Scan Complete BitScpi Command Format HP E1366A/E1367A RF Multiplexers Command ReferenceCommand Types Common Command FormatHP E1366A/E1367A RF Multiplexers Command Reference Chapter Semicolon between the commands. For example Example Stopping a Scan with ABORt Scpi Command ReferenceABORt Subsystem Syntax ABORtParameters Subsystem Syntax ARMExample Query Number of Scanning Cycles DISPlay Example Enabling the Monitor ModeSubsystem Syntax DISPlay Example Select Module #2 in a Switchbox for Monitoring Example Enabling Continuous Scans ∙ Non-Continuous Scanning Operation This is enabled with∙ Stopping Continuous Scans See the ABORt command INITiateExample Query Continuous Scanning State Subsystem Syntax OUTPut Example Enable Trig Out PortExample Query Trig Out Port Enable State OUTPutExample Closing Multiplexer Channels ROUTeSubsystem Syntax ROUTe Comments ∙ Closing Channels To close∙ Opening Channels To open CommentsExample Opening Channels Open Example Scanning Using External Devices Example Selecting Paired-Channel Scanning Example Query Scan Mode∙ Returned Data after sending the STATusOPERationEVENt? ∙ Setting Bit 7 of the Status RegisterSTATus Subsystem Syntax STATusCTYPe? SYSTemSubsystem Syntax SYSTem Example Reading the Model Number of a Card #1 Module ∙ RF Multiplexers Power-On State The power-on state is allExample Setting Card #1 Module to its Power-on State Comments ∙ RF Multiplexers Model NumberTRIGger Example Advancing Scan Using the TRIGger CommandSubsystem Syntax TRIGger ∙ Trig Out Port Shared by Switchboxes See the OUTPut command Example Scanning Using Bus Triggers Example Scanning Using External TriggersExample Query Trigger Source Command Title Description Ieee 488.2 Common CommandsCommands for the RF Multiplexer modules used in a switchbox Command Quick ReferenceGeneral HP E1366A/E1367A RF Multiplexer SpecificationsInput Characteristics AC Performance Appendix a HP E1366A/E1367A RF Multiplexer SpecificationsTypical Crosstalk channel-channel Cooling/Slot HP E1366A/E1367A RF Multiplexer Specifications Appendix aRelay Life End of Life Detection Replacement StrategyHP E1366A/E1367A RF Multiplexer Specifications Appendix a Appendix B HP E1366A/E1367A Multiplexer Registers HP E1366A/E1367A Multiplexer RegistersID Register ID/Device Type Registers Status/Control Register Channel Enable RegistersAddressing the Registers Reading the RegistersWriting to the Registers HP E1366A/E1367A Multiplexer Registers Appendix B Appendix C HP E1366A/E1367A RF Multiplexer Error Messages HP E1366A/E1367A RF Multiplexer Error MessagesHP E1366A/E1367A RF Multiplexer Error Messages Appendix C HP E1366A/67A RF Multiplexers User’s Manual Index IndexHP-IB HP E1366A/67A RF Multiplexers User’s Manual Index HP E1366A/67A RF Multiplexers User’s Manual Index