HP manual Example Standard Switching, Using the HP E1366A/E1367A RF Multiplexer Module Chapter

Page 26

Example: Standard Switching

This example connects channel 02 to com 00 of an RF multiplexer in standard configuration. The multiplexer is defined as a single-multiplexer switchbox instrument. See the following figure for typical user connections. To connect channel 02 to com 00, execute:

CLOS (@102)

! Connect channel 02 to com 00.

1 is the card number and 02 is the

channel number.

To open the channel, use OPEN (@102).

Figure 3-1. Standard Switching

26 Using the HP E1366A/E1367A RF Multiplexer Module

Chapter 3

Image 26

Contents Contents HP E1366A/E1367A RF Multiplexers Command Reference HP E1366A/E1367A RF Multiplexer Specifications HP E1366A/67A RF Multiplexers User’s Manual Contents HP E1366A & E1367A RF Multiplexer Modules User’s Manual Documentation History December 5 According to ISO/IEC Guide 22 and ENHP E1366A & E1367A RF Multiplexer Modules User’s Manual Measurement Systems Division Reader Comment SheetHP E1366A & E1367A RF Multiplexer Module User’s Manual Multiplexer Module Description Using This ChapterGetting Started with the HP E1366A/E1367A RF Multiplexers Multiplexers Switching Diagram Programming the Multiplexer Module Typical ConfigurationSpecifying Scpi Commands AddressMultiplexer Card Numbers Multiplexer Channel NumbersInitial Operation Example RF Multiplexer Channel Lists/RangesPage Configuring the HP E1366A/E1367A RF Multiplexers Chapter Configuring the HP E1366A/E1367A RF MultiplexersConnecting User Inputs Configuring the HP E1366A/E1367A RF Multiplexers ChapterHewlett-Packard BNC Cables Typical Multiplexer Configurations Standard ConfigurationTypical Tree Configuration Matrix-Type Configuration Typical Matrix-Type ConfigurationChanging Multiplexer Components RF Multiplexer Component LocationsConfiguring the HP E1366A/E1367A RF Multiplexers Chapter Switching Channels Using the HP E1366A/E1367A RF Multiplexer ModuleMultiplexer Commands Chapter Using the HP E1366A/E1367A RF Multiplexer ModuleExample Standard Switching Using the HP E1366A/E1367A RF Multiplexer Module ChapterExample Tree Switching Tree SwitchingExample Matrix-Type Switching Query Channel States. Use CLOSe? channellist orExample Scanning Using Trig Out Port Scanning ChannelsScanning Channels Comments Understanding the HP E1366A/E1367A RF Multiplexers Scanning Channels CommandsUsing Scanning Trigger Sources Scanning with External InstrumentsUnderstanding the HP E1366A/E1367A RF Multiplexers Chapter Scanning Trigger Sources Example Scanning with External Device Scanning with External DeviceExample Scanning Using Trig Out Event Ports Using the Scan Complete Bit Example Scan Complete InterruptCommon Command Format HP E1366A/E1367A RF Multiplexers Command ReferenceCommand Types Scpi Command FormatHP E1366A/E1367A RF Multiplexers Command Reference Chapter Semicolon between the commands. For example Subsystem Syntax ABORt Scpi Command ReferenceABORt Example Stopping a Scan with ABORtSubsystem Syntax ARM ParametersExample Query Number of Scanning Cycles Subsystem Syntax DISPlay Example Enabling the Monitor ModeDISPlay Example Select Module #2 in a Switchbox for Monitoring INITiate ∙ Non-Continuous Scanning Operation This is enabled with∙ Stopping Continuous Scans See the ABORt command Example Enabling Continuous ScansExample Query Continuous Scanning State OUTPut Example Enable Trig Out PortExample Query Trig Out Port Enable State Subsystem Syntax OUTPutComments ∙ Closing Channels To close ROUTeSubsystem Syntax ROUTe Example Closing Multiplexer ChannelsExample Opening Channels Comments∙ Opening Channels To open Open Example Scanning Using External Devices Example Query Scan Mode Example Selecting Paired-Channel ScanningSubsystem Syntax STATus ∙ Setting Bit 7 of the Status RegisterSTATus ∙ Returned Data after sending the STATusOPERationEVENt?Subsystem Syntax SYSTem SYSTemCTYPe? Comments ∙ RF Multiplexers Model Number ∙ RF Multiplexers Power-On State The power-on state is allExample Setting Card #1 Module to its Power-on State Example Reading the Model Number of a Card #1 ModuleSubsystem Syntax TRIGger Example Advancing Scan Using the TRIGger CommandTRIGger ∙ Trig Out Port Shared by Switchboxes See the OUTPut command Example Query Trigger Source Example Scanning Using External TriggersExample Scanning Using Bus Triggers Ieee 488.2 Common Commands Command Title DescriptionCommand Quick Reference Commands for the RF Multiplexer modules used in a switchboxAppendix a HP E1366A/E1367A RF Multiplexer Specifications HP E1366A/E1367A RF Multiplexer SpecificationsInput Characteristics AC Performance GeneralHP E1366A/E1367A RF Multiplexer Specifications Appendix a Typical Crosstalk channel-channel Cooling/SlotEnd of Life Detection Replacement Strategy Relay LifeHP E1366A/E1367A RF Multiplexer Specifications Appendix a ID Register HP E1366A/E1367A Multiplexer RegistersAppendix B HP E1366A/E1367A Multiplexer Registers Reading the Registers Status/Control Register Channel Enable RegistersAddressing the Registers ID/Device Type RegistersWriting to the Registers HP E1366A/E1367A Multiplexer Registers Appendix B HP E1366A/E1367A RF Multiplexer Error Messages Appendix C HP E1366A/E1367A RF Multiplexer Error MessagesHP E1366A/E1367A RF Multiplexer Error Messages Appendix C Index HP E1366A/67A RF Multiplexers User’s Manual IndexHP-IB HP E1366A/67A RF Multiplexers User’s Manual Index HP E1366A/67A RF Multiplexers User’s Manual Index