HP E1367A, E1366A manual Semicolon between the commands. For example

Page 39

Parameters Parameter Types. The following table contains explanations and examples of parameter types you might see later in this chapter.

Table 5-1. SCPI Parameter Types

Parameter Type	Explanations and Examples

Numeric	Accepts all commonly used decimal representations of
	numbers including optional signs, decimal points, and
	scientific notation.
	123, 123E2, -123, -1.23E2, .123, 1.23E-2, 1.23000E-01.
	Special cases include MIN, MAX, and INF.

Boolean	Represents a single binary condition that is either
	true or false.
	ON, OFF, 1, 0.

Discrete	Selects from a finite number of values. These parameters
	use mnemonics to represent each valid setting.
	An example is the TRIGger:SOURce <source> command
	where <source> can be BUS, EXT, HOLD, or IMM.

Optional Parameters. Parameters shown within square brackets ( [ ] ) are optional parameters. (Note that the brackets are not part of the command and are not sent to the instrument.) If you do not specify a value for an optional parameter, the instrument chooses a default value. For example, consider the ARM:COUNt? [<MIN MAX>] command. If you send the command without specifying a parameter, the present ARM:COUNt value is returned. If you send the MIN parameter, the command returns the minimum count available. If you send the MAX parameter, the command returns the maximum count available. Be sure to place a space between the command and the parameter.

Linking Commands Linking IEEE 488.2 Common Commands with SCPI Commands. Use

a semicolon (;) between the commands. For example:

*RST;OUTP ON

or

TRIG:SOUR HOLD;*RST

Linking Multiple SCPI Commands. Use both a semicolon (;) and a colon (:) between the commands. For example:

ARM COUN 1;:TRIG:SOUR EXT

Chapter 5

HP E1366A/E1367A RF Multiplexers Command Reference 39

Image 39

Contents Contents HP E1366A/E1367A RF Multiplexers Command Reference HP E1366A/E1367A RF Multiplexer Specifications HP E1366A/67A RF Multiplexers User’s Manual Contents HP E1366A & E1367A RF Multiplexer Modules User’s Manual Documentation History According to ISO/IEC Guide 22 and EN December 5HP E1366A & E1367A RF Multiplexer Modules User’s Manual Reader Comment Sheet Measurement Systems DivisionHP E1366A & E1367A RF Multiplexer Module User’s Manual Using This Chapter Getting Started with the HP E1366A/E1367A RF MultiplexersMultiplexer Module Description Multiplexers Switching Diagram Address Typical ConfigurationSpecifying Scpi Commands Programming the Multiplexer ModuleMultiplexer Channel Numbers Multiplexer Card NumbersExample RF Multiplexer Channel Lists/Ranges Initial OperationPage Chapter Configuring the HP E1366A/E1367A RF Multiplexers Configuring the HP E1366A/E1367A RF MultiplexersConfiguring the HP E1366A/E1367A RF Multiplexers Chapter Connecting User InputsHewlett-Packard BNC Cables Standard Configuration Typical Multiplexer ConfigurationsTypical Tree Configuration Typical Matrix-Type Configuration Matrix-Type ConfigurationRF Multiplexer Component Locations Changing Multiplexer ComponentsConfiguring the HP E1366A/E1367A RF Multiplexers Chapter Chapter Using the HP E1366A/E1367A RF Multiplexer Module Using the HP E1366A/E1367A RF Multiplexer ModuleMultiplexer Commands Switching ChannelsUsing the HP E1366A/E1367A RF Multiplexer Module Chapter Example Standard SwitchingTree Switching Example Tree SwitchingQuery Channel States. Use CLOSe? channellist or Example Matrix-Type SwitchingScanning Channels Example Scanning Using Trig Out PortScanning Channels Comments Scanning with External Instruments Scanning Channels CommandsUsing Scanning Trigger Sources Understanding the HP E1366A/E1367A RF MultiplexersUnderstanding the HP E1366A/E1367A RF Multiplexers Chapter Scanning Trigger Sources Scanning with External Device Example Scanning with External DeviceExample Scanning Using Trig Out Event Ports Example Scan Complete Interrupt Using the Scan Complete BitScpi Command Format HP E1366A/E1367A RF Multiplexers Command ReferenceCommand Types Common Command FormatHP E1366A/E1367A RF Multiplexers Command Reference Chapter Semicolon between the commands. For example Example Stopping a Scan with ABORt Scpi Command ReferenceABORt Subsystem Syntax ABORtParameters Subsystem Syntax ARMExample Query Number of Scanning Cycles Example Enabling the Monitor Mode DISPlaySubsystem Syntax DISPlay Example Select Module #2 in a Switchbox for Monitoring Example Enabling Continuous Scans ∙ Non-Continuous Scanning Operation This is enabled with∙ Stopping Continuous Scans See the ABORt command INITiateExample Query Continuous Scanning State Subsystem Syntax OUTPut Example Enable Trig Out PortExample Query Trig Out Port Enable State OUTPutExample Closing Multiplexer Channels ROUTeSubsystem Syntax ROUTe Comments ∙ Closing Channels To closeComments ∙ Opening Channels To openExample Opening Channels Open Example Scanning Using External Devices Example Selecting Paired-Channel Scanning Example Query Scan Mode∙ Returned Data after sending the STATusOPERationEVENt? ∙ Setting Bit 7 of the Status RegisterSTATus Subsystem Syntax STATusSYSTem CTYPe?Subsystem Syntax SYSTem Example Reading the Model Number of a Card #1 Module ∙ RF Multiplexers Power-On State The power-on state is allExample Setting Card #1 Module to its Power-on State Comments ∙ RF Multiplexers Model NumberExample Advancing Scan Using the TRIGger Command TRIGgerSubsystem Syntax TRIGger ∙ Trig Out Port Shared by Switchboxes See the OUTPut command Example Scanning Using External Triggers Example Scanning Using Bus TriggersExample Query Trigger Source Command Title Description Ieee 488.2 Common CommandsCommands for the RF Multiplexer modules used in a switchbox Command Quick ReferenceGeneral HP E1366A/E1367A RF Multiplexer SpecificationsInput Characteristics AC Performance Appendix a HP E1366A/E1367A RF Multiplexer SpecificationsTypical Crosstalk channel-channel Cooling/Slot HP E1366A/E1367A RF Multiplexer Specifications Appendix aRelay Life End of Life Detection Replacement StrategyHP E1366A/E1367A RF Multiplexer Specifications Appendix a HP E1366A/E1367A Multiplexer Registers Appendix B HP E1366A/E1367A Multiplexer RegistersID Register ID/Device Type Registers Status/Control Register Channel Enable RegistersAddressing the Registers Reading the RegistersWriting to the Registers HP E1366A/E1367A Multiplexer Registers Appendix B Appendix C HP E1366A/E1367A RF Multiplexer Error Messages HP E1366A/E1367A RF Multiplexer Error MessagesHP E1366A/E1367A RF Multiplexer Error Messages Appendix C HP E1366A/67A RF Multiplexers User’s Manual Index IndexHP-IB HP E1366A/67A RF Multiplexers User’s Manual Index HP E1366A/67A RF Multiplexers User’s Manual Index