HP manual HP E1366A/E1367A RF Multiplexer Error Messages

Page 69

Appendix C

HP E1366A/E1367A RF Multiplexer Error Messages

		The table below lists the error messages associated with the multiplexer
		modules programmed by SCPI. See the appropriate mainframe manual for
		a complete list of error messages.

No.	Title	Potential Cause(s)

-211	Trigger ignored	Trigger received when scan not enabled. Trigger received after scan complete.
		Trigger too fast.

-213	Init Ignored	Attempting to execute an INIT command when a scan is already in progress.

-224	Illegal parameter value	Attempting to execute a command with a parameter not applicable to the command.

1500	External trigger source	Assigning an external trigger source to a switchbox when the trigger source has
	already allocated	already been assigned to another switchbox.

2000	Invalid card number	Addressing a module (card) in a switchbox that is not part of the switchbox.

2001	Invalid channel number	Attempting to address a channel of a module in a switchbox that is not supported by
		the module (e.g., channel 99 of a multiplexer module).

2006	Command not supported	Sending a command to a module (card) in a switchbox that is unsupported by the
	on this card	module.

2008	Scan list not initialized	Executing a scan without the INIT command.

2009	Too many channels in	Attempting to address more channels than available in the switchbox.
	channel list

2012	Invalid Channel Range	Invalid channel(s) specified in SCAN <channel_list> command. Attempting to begin
		scanning when no valid channel l t is defined.

2600	Function not supported	Sending a command to a module (card) in a switchbox that is not supported by the
	on this card	module or switchbox.

2601	Channel list required	Sending a command requiring a channel list without the channel list.

Appendix C

HP E1366A/E1367A RF Multiplexer Error Messages 69

Image 69

Contents Contents HP E1366A/E1367A RF Multiplexers Command Reference HP E1366A/E1367A RF Multiplexer Specifications HP E1366A/67A RF Multiplexers User’s Manual Contents HP E1366A & E1367A RF Multiplexer Modules User’s Manual Documentation History According to ISO/IEC Guide 22 and EN December 5HP E1366A & E1367A RF Multiplexer Modules User’s Manual Reader Comment Sheet Measurement Systems DivisionHP E1366A & E1367A RF Multiplexer Module User’s Manual Using This Chapter Getting Started with the HP E1366A/E1367A RF MultiplexersMultiplexer Module Description Multiplexers Switching Diagram Specifying Scpi Commands Typical ConfigurationProgramming the Multiplexer Module AddressMultiplexer Channel Numbers Multiplexer Card NumbersExample RF Multiplexer Channel Lists/Ranges Initial OperationPage Chapter Configuring the HP E1366A/E1367A RF Multiplexers Configuring the HP E1366A/E1367A RF MultiplexersConfiguring the HP E1366A/E1367A RF Multiplexers Chapter Connecting User InputsHewlett-Packard BNC Cables Standard Configuration Typical Multiplexer ConfigurationsTypical Tree Configuration Typical Matrix-Type Configuration Matrix-Type ConfigurationRF Multiplexer Component Locations Changing Multiplexer ComponentsConfiguring the HP E1366A/E1367A RF Multiplexers Chapter Multiplexer Commands Using the HP E1366A/E1367A RF Multiplexer ModuleSwitching Channels Chapter Using the HP E1366A/E1367A RF Multiplexer ModuleUsing the HP E1366A/E1367A RF Multiplexer Module Chapter Example Standard SwitchingTree Switching Example Tree SwitchingQuery Channel States. Use CLOSe? channellist or Example Matrix-Type SwitchingScanning Channels Example Scanning Using Trig Out PortScanning Channels Comments Using Scanning Trigger Sources Scanning Channels CommandsUnderstanding the HP E1366A/E1367A RF Multiplexers Scanning with External InstrumentsUnderstanding the HP E1366A/E1367A RF Multiplexers Chapter Scanning Trigger Sources Scanning with External Device Example Scanning with External DeviceExample Scanning Using Trig Out Event Ports Example Scan Complete Interrupt Using the Scan Complete BitCommand Types HP E1366A/E1367A RF Multiplexers Command ReferenceCommon Command Format Scpi Command FormatHP E1366A/E1367A RF Multiplexers Command Reference Chapter Semicolon between the commands. For example ABORt Scpi Command ReferenceSubsystem Syntax ABORt Example Stopping a Scan with ABORtParameters Subsystem Syntax ARMExample Query Number of Scanning Cycles Example Enabling the Monitor Mode DISPlaySubsystem Syntax DISPlay Example Select Module #2 in a Switchbox for Monitoring ∙ Stopping Continuous Scans See the ABORt command ∙ Non-Continuous Scanning Operation This is enabled withINITiate Example Enabling Continuous ScansExample Query Continuous Scanning State Example Query Trig Out Port Enable State Example Enable Trig Out PortOUTPut Subsystem Syntax OUTPutSubsystem Syntax ROUTe ROUTeComments ∙ Closing Channels To close Example Closing Multiplexer ChannelsComments ∙ Opening Channels To openExample Opening Channels Open Example Scanning Using External Devices Example Selecting Paired-Channel Scanning Example Query Scan ModeSTATus ∙ Setting Bit 7 of the Status RegisterSubsystem Syntax STATus ∙ Returned Data after sending the STATusOPERationEVENt?SYSTem CTYPe?Subsystem Syntax SYSTem Example Setting Card #1 Module to its Power-on State ∙ RF Multiplexers Power-On State The power-on state is allComments ∙ RF Multiplexers Model Number Example Reading the Model Number of a Card #1 ModuleExample Advancing Scan Using the TRIGger Command TRIGgerSubsystem Syntax TRIGger ∙ Trig Out Port Shared by Switchboxes See the OUTPut command Example Scanning Using External Triggers Example Scanning Using Bus TriggersExample Query Trigger Source Command Title Description Ieee 488.2 Common CommandsCommands for the RF Multiplexer modules used in a switchbox Command Quick ReferenceInput Characteristics AC Performance HP E1366A/E1367A RF Multiplexer SpecificationsAppendix a HP E1366A/E1367A RF Multiplexer Specifications GeneralTypical Crosstalk channel-channel Cooling/Slot HP E1366A/E1367A RF Multiplexer Specifications Appendix aRelay Life End of Life Detection Replacement StrategyHP E1366A/E1367A RF Multiplexer Specifications Appendix a HP E1366A/E1367A Multiplexer Registers Appendix B HP E1366A/E1367A Multiplexer RegistersID Register Addressing the Registers Status/Control Register Channel Enable RegistersReading the Registers ID/Device Type RegistersWriting to the Registers HP E1366A/E1367A Multiplexer Registers Appendix B Appendix C HP E1366A/E1367A RF Multiplexer Error Messages HP E1366A/E1367A RF Multiplexer Error MessagesHP E1366A/E1367A RF Multiplexer Error Messages Appendix C HP E1366A/67A RF Multiplexers User’s Manual Index IndexHP-IB HP E1366A/67A RF Multiplexers User’s Manual Index HP E1366A/67A RF Multiplexers User’s Manual Index