HP DreamColor Z24x Professional Display manual Changing the Bezel Button Functions

Page 37

Connect from the DisplayPort OUT of one monitor to the DisplayPort IN of the next, until you have the desired number of displays.

If you want different information on each screen be sure that all upstream monitors are configured to DisplayPort 1.2 mode, as described above.

The number of monitors you can connect through DisplayPort multistreaming depends on a number of factors, including the resolutions and scan rates used for each monitor and the capabilities of your GPU or embedded graphics system. Check the manual that came with your graphics card for further information on its capabilities.

Changing the Bezel Button Functions

You can change the top-level front bezel button functions from their default values so that when the buttons are activated you can quickly access commonly used menu items.

To change the bezel button functions:

1.Press one of the five front bezel buttons to activate the buttons, and then press the bottom Open Menu button to open the OSD.

2.In the OSD, select Menu and Message Control > Configure Function Buttons and then select one of the available options for the button you want to reconfigure.

Adjusting the Bezel Button LEDs

The bezel button LEDs have an automatic fade-out feature that is active by default. The LEDs will fade after the OSD timeout period. You can change the LED behavior so that they do not fade out and you can also adjust the brightness of the LEDs if the fade-out feature is disabled.

To disable the bezel button fade-out feature:

1.Press one of the five front bezel buttons to activate the buttons, and then press the bottom Open Menu button to open the OSD.

2.In the OSD, select Menu and Message Control > Bezel Button Auto-Fade > Disable (Always On).

If the bezel button fade-out feature has been disabled (as described above), you can adjust the brightness of the buttons on the front bezel to different levels of ambient lighting.

To change the bezel button brightness:

1.Press one of the five front bezel buttons to activate the buttons, and then press the bottom Open Menu button to open the OSD.

2.In the OSD, select Menu and Message Control > Bezel Button Brightness and use the adjustment scale to set the buttons to the desired brightness.

Using Auto-Sleep Mode

The display supports an OSD (On-Screen Display) option called Auto-Sleep Mode that allows you to enable or disable a reduced power state for the display. When Auto-Sleep Mode is enabled (enabled by default), the monitor will enter a reduced power state when the host PC signals low power mode (absence of either horizontal or vertical sync signal).

Changing the Bezel Button Functions 29

Page 36 Page 38
Image 37
Page 36 Page 38
Contents HP DreamColor Z24x Display Hewlett-Packard Development Company, L.P About This Guide Iv About This Guide Table of contents Z24x Model Recognizing Preset Display Resolutions Vii Viii Z24x Display Product FeaturesPage Important Safety Information Safety and Maintenance GuidelinesCleaning the Monitor Maintenance GuidelinesShipping the Monitor Use Caution When Setting Up the Monitor Setting Up the MonitorInstalling the Stand Component Function Rear ComponentsConnecting the Cables Page Page Page Page Front Panel Controls Adjusting the Monitor Page Setting Up the Monitor Turning on the Monitor HP Watermark and Image Retention Policy Connecting USB DevicesRemoving the Monitor Stand Mounting the Monitor Page Page Page Locating the Information Card Locating the Serial Number and Product NumberInstalling a Cable Lock Software and Utilities Operating the MonitorInformation File Image Color Matching FileUsing Picture-in-Picture PIP and Picture-beside-Picture PBP Installing the .INF and .ICM FilesInstalling from the Disc Downloading from the InternetDisplayPort Multistreaming Using Auto-Sleep Mode Adjusting the Bezel Button LEDsChanging the Bezel Button Functions Using the On-Screen Display Menu Level DVI Hdmi Primary / PIP Source Information Operating the Monitor Back Factory Reset Color Management Color PresetsColor Calibration Factory Color Calibration UserAuto Edid Update Z24x Model Technical SpecificationsPreset Pixel Format Aspect Ratio Vert Freq Hz Pixel Clk MHz Recognizing Preset Display ResolutionsSolving Common Problems Support and TroubleshootingPreparing to Call Technical Support Product SupportPage Federal Communications Commission Notice Agency Regulatory NoticesModifications CablesAvis Canadien Canadian NoticeEuropean Union Regulatory Notice Japanese Power Cord Requirements Japanese Notice Korean Notice Power Cord Set RequirementsGerman Ergonomics Notice Energy Star Qualification Product Environmental NoticesMaterials Disposal Product Environmental Notices Ukraine Restriction of Hazardous Substances Turkey EEE RegulationLCD Monitor Quality and Pixel Policy
Top Page Image Contents