ASRock Version 1.0 manual Specifications

Page 6

1.2Specifications

Platform

- Micro ATX Form Factor: 9.6-in x 8.4-in, 24.4 cm x 21.3 cm

CPU

- LGA 775 for Intel® CoreTM 2 Extreme / CoreTM 2 Quad / CoreTM

 

2 Duo / Pentium® Dual Core / Celeron®, supporting Penryn Quad

 

Core Yorkfield and Dual Core Wolfdale processors

 

- Compatible with all FSB1600/1333/1066/800MHz CPUs

 

(see CAUTION 1)

 

- Supports Hyper-Threading Technology (see CAUTION 2)

 

- Supports Untied Overclocking Technology (see CAUTION 3)

 

- Supports EM64T CPU

Chipset

- Northbridge: Intel® G31

 

- Southbridge: Intel® ICH7

Memory

- Dual Channel DDR2 Memory Technology (see CAUTION 4)

 

- 2 x DDR2 DIMM slots

 

- Support DDR2 800/667 non-ECC, un-buffered memory

 

(see CAUTION 5)

 

- Max. capacity of system memory: 4GB (see CAUTION 6)

Hybrid Booster

- CPU Frequency Stepless Control (see CAUTION 7)

 

- ASRock U-COP (see CAUTION 8)

 

- Boot Failure Guard (B.F.G.)

Expansion Slot

- 1 x PCI Express x16 slot

 

- 1 x PCI Express x1 slot

 

- 2 x PCI slots

Graphics

- Intel® Graphics Media Accelerator 3100

 

- Pixel Shader 2.0, DirectX 9.0

 

- Max. shared memory 384MB (see CAUTION 9)

Audio

- 5.1 CH Windows® VistaTM Premium Level HD Audio

 

(ALC662 Audio Codec)

LAN

- Realtek PCIE x1 LAN 8102E

 

- Speed: 10/100 Ethernet

 

- Supports Wake-On-LAN

Rear Panel I/O

ASRock 6CH I/O

 

- 1 x PS/2 Mouse Port

 

- 1 x PS/2 Keyboard Port

 

- 1 x Serial Port: COM1

 

- 1 x VGA Port

 

- 1 x Parallel Port (ECP/EPP Support)

 

- 4 x Ready-to-Use USB 2.0 Ports

 

- 1 x RJ-45 LAN Port

 

- HD Audio Jack: Line in / Front Speaker / Microphone

6

Image 6
Contents 4Core1600-D800 Copyright Notice DisclaimerContents Software Support Package Contents IntroductionSpecifications Support CD ConnectorBios Feature HardwarePage CPU Motherboard Layout ATXPWR1ASRock 6CH I/O For Windows XPPre-installation Precautions Screw HolesCPU Installation Page Installation of CPU Fan and Heatsink Installation of Memory Modules Dimm Installing a DimmInstalling an expansion card Expansion Slots PCI and PCI Express SlotsJumpers Setup PS2USBPWR1Onboard Headers and Connectors IDE1USB 2.0 Headers Chassis Speaker Header ATX Power Connector Sataii Hard Disk Setup Guide Western DigitalDriver Installation Guide Untied Overclocking TechnologyBios Menu Bar Navigation Keys Main ScreenAdvanced Screen CPU Configuration Enhance Halt State Ratio StatusRatio Actual Value Max Cpuid Value LimitChipset Configuration Dram RAS# Precharge Internal Graphics Mode SelectDvmt Mode Select Dram RAS# Activate to PrechargeNB Core Voltage Dram Rcomp SettingDram Voltage VTT VoltageAcpi Configuration Acpi Hpet Table IDE ConfigurationATA/IDE Configuration Combined OptionPIO Mode IDE Device ConfigurationLBA/Large Mode Block Multi-Sector TransferPCIPnP Configuration OnBoard Floppy Controller Floppy ConfigurationSuper IO Configuration Serial Port AddressParallel Port Address Parallel Port ModeECP Mode DMA Channel EPP VersionUSB 2.0 Support USB Controller EnabledUSB Controller Legacy USB SupportCPU Quiet Fan Target CPU TemperatureHardware Health Event Monitoring Screen Target Fan SpeedMain Advanced Monitor Boot ScreenBoot Settings Configuration Security ExitBoot Up Num-Lock Boot Settings ConfigurationBoot From Onboard LAN Security ScreenSave Changes and Exit Load Optimal DefaultsExit Screen Discard Changes and ExitRunning The Support CD Install Operating SystemSupport CD Information Drivers Menu