MSI H87M-G43 manual Chapter

Page 27

3.Align the notches with the socket alignment keys. Lower the CPU straight down, without tilting or sliding the CPU in the socket. Inspect the CPU to check if it is properly seated in the socket.

4.Close and slide the load plate under the retention knob. Close and engage the load lever.

CPU notches

Chapter 1

Alignment Key

Retention knob

5.When you press down the load lever the PnP cap will automatically pop up from the CPU socket. Do not discard the PnP cap. Always replace the PnP cap if the CPU is removed from the socket.

6.Evenly spread a thin layer of thermal paste (or thermal tape) on the top of the CPU. This will help in heat dissipation and prevent CPU overheating.

PnP cap

Thermal paste

1-13

Getting Started

Image 27
Contents G52-78231X1 PrefacePreface Smartphone Application Technical Support IT MAY Damage the Equipment Safety InstructionsFCC-B Radio Frequency Interference Statement Voir LA Notice D’INSTALLATION Avant DE Raccorder AU ReseauKorea Warning Statements Battery Information Weee Waste Electrical and Electronic Equipment Statement Español Türkçe Contents OC Profile Hardware Monitor Quick InstallationAppendix a Intel SBA optional Page Chapter Optional Accessories Packing ContentsAssembly Precautions Motherboard Specifications CPUUSB Bios Uefi AMI BiosLAN MSI Connectors Quick Guide Connectors Reference Guide Back Panel Quick Guide HDMI+VGA HDMI+DVI Introduction to the LGA 1150 CPU CPU Central Processing UnitVideo Demonstration CPU & Heatsink InstallationChapter Chapter Memory Dual -Channel mode Population RuleMounting Screw Holes JPWR1 Power SupplyJPWR1~2 ATX Power Connectors JPWR2PCIE1~4 PCIe Expansion Slots Expansion SlotsVideo/ Graphics Cards Single Video Card InstallationAMD CrossFire Multi -GPU Technology Chapter SATA1 Internal ConnectorsSATA1~6 Sata Connectors SATA2 SATA4 SATA6 SATA3 SATA5CPUFAN1,SYSFAN1~2 Fan Power Connectors JFP1, JFP2 System Panel Connectors JFP2JFP1 JUSB1~3 USB 2.0 Expansion Connectors JAUD1 Front Panel Audio Connector JUSB4 USB 3.0 Expansion ConnectorJCOM1 Serial Port Connector JTPM1 TPM Module ConnectorJCI1 Chassis Intrusion Connector JLPT1 Parallel Port ConnectorJBAT1 Clear Cmos Jumper JumpersDrivers and Utilities Total InstallerQuick Installation CPU Installation Chapter Memory Installation Motherboard Installation Chapter Power Connectors Installation Chapter Sata HDD Installation MSATA SSD Installation Front Panel Connector Installation JFP1 Connector InstallationFront Panel Audio Connector Installation Peripheral Connector Installation USB2.0 Connector InstallationUSB3.0 Connector Installation Graphics Card Installation Chapter Bios Setup Entering Setup Entering Bios SetupPress DEL key to enter Setup Menu, F11 to enter Boot Menu Overview Bar Operation System Status SettingsAdvanced PEG IGDPartition size must be larger then the amount of memory SSD speed ECP SPPRequirement Boot settings Events LEGACY+UEFI BootSecurity UefiSave & Exit This setting will be configured automatically by Bios Next Boot Profile Booting to accelerate the system booting time Over-current protection MEMORY-Z Enabled Enables Intel AES support Disabled SSD speed Flash OC Profile Hardware Monitor Chapter Appendix a Prerequisites Appendix aInstalling Intel SBA Software ConfigurationSoftware panel overview Help Button Password settingsAppendix B Introduction Appendix BUsing Intel Rapid Storage Technology Option ROM XXX.X GB Appendix B XXXX-XXXXXXXX Press Y key to accept the volume deletion XXXX-XXXXXXXX Recovery Volume Options Main Menu Degraded RAID ArrayAppendix B System Acceleration optional Appendix B Disk Port RST Synchronization optional