Pentair ThermalFlo Drainage and Condensation, Lawn Sprinklers, Anchor Clamps Installation

Page 14
NO SPRINKLERS
WITHIN A 6 FT. RANGE
Figure 3.

6

Drainage and Condensation

Condensation will occur from the evaporator coil while the unit is running and drain at a steady rate, usually three to five gallons per hour, depending upon ambient air temperature and humidity. The more humid the ambient conditions, the more condensation will be produced. The bottom of the unit acts as a tray to catch rainwater and condensation. Keep the drain holes, located on the bottom pan of the base of the unit, clear of debris.

Lawn Sprinklers

Make sure there are absolutely no sprinkler heads near the heater that will in any way spray on or into the heater. Sprinkler damage is not covered under the warranty agreement.

Make sure that they’re a sufficient distance away so that normal winds will not carry the mist to the heater. If your filtering system area has plants that need water, use a trickle type irrigation sprinkler instead of the broadcast type.

The heater is designed to handle the wettest weather conditions that are typical of rain and humidity, etc. Sprinkler heads force high pressure water into the unit from

the side at an odd angle. Most sprinkler systems are connected to a well system. Most well water is high in minerals, sulphur and other aggressive contaminates. These contaminates will leave a build up on the evaporator coils and electronics causing corrosion and hamper the efficiency. If you are located within 15 miles of the coast, salt may also be in the well water.

Anchor Clamp(s) Installation

In Florida, building codes require that the heat pump be anchored to the equipment pad or platform to withstand high wind pressures created during hurricanes.

This heat pump is provided with anchor clamps designed to hold the unit to the equipment pad in high wind conditions. Installation of the anchor clamps are recommended in all installations and are required in Florida (See Florida Building Code 301.13).

To install the anchor clamps:

1.Be sure that the heat pump is in its permanent location on the equipment pad.

2.Remove the anchor clamps from the installation and instruction package.

Note: Bolts and bolt anchors are not included with the heat pump. The installer must provide 1/4” x 1-3/8” stainless steel anchor bolts and the appropriate size concrete anchor to mount the clamp to the equipmentpad.

3.Place the clamps at the base of the heat pump in the locations indicated in Figure 4, (2 in. undercut [notched area] on either side).

4.Fit the hook of each clamp over the lip on the base panel of the heatpump.Thehookshouldfitbetweenthelipofthebasepanel and the evaporator coil guard, see Figure 5.

5.Markthepositionoftheholeineachclampontheequipmentpad.

HEAT PUMP

CLAMPS

HEAT PUMP

CLAMPS

Figure 4.

ThermalFlo Installation and User’s Guide

Page 13 Page 15
Image 14
Page 13 Page 15
Contents ThermalFlo Customer Service Web siteContents Illustrated Parts Replacement Parts List Important Notice Codes and StandardsImportant Safety Precautions Consumer Information and SafetySwimming Pool Energy Saving Tips Warranty Information General Installation InformationGeneral Specifications Section Introduction ThermalFlo OverviewGeneral Features Materials needed for Installation Section InstallationInstalling the ThermalFlo ThermalFlo Heat Pump Dimensions LocationEquipment Pad ClearancesRoof Run-off Lawn Sprinklers Anchor Clamps InstallationDrainage and Condensation Water Connections Plumbing layoutAutomatic Flow Control Valve Check Valve InstallationWater Connections at the Heat Pump Multiple Unit Installation Heat Pump, Heater and/or Solar CombinationMultiple Heat Pump Connections To PoolGeneral Information Main PowerElectrical Connections BondingWiring Diagram 460812, 460813, 460814, 460815, 460822Relay Remote Controls Heat Pump Control BoardBLK GRN YEL RED Initial Start-up Precautions Section Operating ThermalFloOperating the Controller Water Pressure Thermostat Heating CoolingMode Indicator LEDs Indicator Lights / LEDsSystem Indicator LEDs Operation Temperature SettingMode Selection Buttons Keypad LockoutTroubleshooting Code Name CauseWater Pressure Switch Adjustment Winterizing Section General MaintenanceWater Chemistry Owner Inspection Inspection and ServiceSpring Start-Up Professional Maintenance and Service AIRThermalFlo Installation and User’s Guide Section Troubleshooting Remote, Pool or Spa light onDealer for advice. Call the factory for advice Pressure Section Replacement Parts Illustrated PartsReplacement Parts List 25 473026 Compressor Isolation KIT, Grommet & Spacer 1 SETThermalFlo Installation and User’s Guide Page 473426 Rev. C 10/19/06

ThermalFlo specifications

Pentair ThermalFlo is a leading-edge solution designed to address the evolving demands of thermal management in various industrial applications. As organizations prioritize energy efficiency and temperature regulation, ThermalFlo emerges as a robust offering from Pentair, a global leader in water and fluid management.

One of the standout features of Pentair ThermalFlo is its innovative heat tracing technology. This system employs electrical heat tracing cables that are strategically engineered to maintain desired temperatures in pipes, valves, and other critical components. The design minimizes the risks of freezing, ensuring that fluids can flow seamlessly, even in harsh environments. Moreover, it enhances safety by reducing the likelihood of pipe bursts due to thermal stress.

ThermalFlo also incorporates advanced insulation technologies that complement its heat tracing capabilities. The combination of these two approaches ensures optimal energy efficiency, reducing heat loss and lowering operational costs. When used in conjunction with smart monitoring systems, organizations can achieve real-time temperature control, allowing for proactive adjustments that enhance system efficiency.

Another significant characteristic of Pentair ThermalFlo is its versatility. This solution can be customized to suit various applications, from oil and gas industries to food processing and pharmaceuticals. The adaptability of ThermalFlo makes it an ideal choice for facilities looking to improve their thermal strategies without compromising on performance.

In addition to its technical features, Pentair ThermalFlo emphasizes sustainability. By promoting energy efficiency and reducing heat loss, the system contributes to lower carbon footprints for its users. This aligns with the growing trend of adopting environmentally responsible practices within industry, showcasing Pentair’s commitment to innovative solutions that meet modern challenges.

Furthermore, the installation and maintenance of ThermalFlo systems are streamlined, with user-friendly features that simplify the process for engineers and technicians. Its robust design ensures long-lasting performance, reducing downtime and maintenance costs over time.

In conclusion, Pentair ThermalFlo stands out in the marketplace through its blend of innovative technologies, energy efficiency, and adaptability across different industries. As businesses increasingly seek effective thermal management solutions, ThermalFlo represents an investment in reliability, safety, and sustainability.
Top Page Image Contents