Optima Company 600 - 1700 manual Particle filter, Evaporator, Snow and ice

Page 27

Particle filter

It is the particle filter (dirt filter) that ensures no particles or dirt enter the heat pump. Over time the filter can become clogged and must be cleaned. To clean the filter:

1.Shut down the heat pump using the ON/OFF button.

2.Close the valve and unscrew the sealing cap.

3.Loosen the circlip holding the screen in the valve. Use the supplied circlip pliers.

4.Lift out the screen from the valve and wash clean with water.

5.Refit the screen, the circlip and sealing cap.

6.Open the valve and start the heat pump using the ON/OFF button.

Screen

Circlip

Sealing cap

Evaporator

When you notice a coating (for example dust or dirt) on the surface of the evaporator (coil fins), you should wipe it off. The fins are extremely sensitive. Never wipe, e.g. with a cloth, directly on the delicate fins. Use protective gloves to protect your hands from cuts.

This is what to do:

1.Shut down the heat pump using the ON/OFF button.

2.Optima 600-1100:Unscrew the screws and remove the protective grille from the reverse of the heat pump.

Optima 1400-1700:Here you will find an evaporator on the front and rear sides. Detach the covers as described in Unscrew the protec- tive covers. The rear cover can only be tilted outwards because the pipes are connected here.

3.Spray a degreasing agent on the fins of the evaporator.

4.Rinse off the coating and degreasing agent with water. Do not expose the fins to too high a water spray pressure as this can damage them. When the evaporator is extremely dirty you can rinse the coil from inside the inspection hatch. Any cleaning agent is collected in the drainage hose.

Snow and ice

In some locations during periods of snow, snow can accumulate inside the protective grille on the rear side (Optima 600-1100). Remove the grille and carefully brush away the snow without damaging the fins. It is not necessary to refit the grille. If snow attaches/sticks to the holes of the protective covers, brush it off (all Optimas).

Also remove any snow or ice from the grille on top of the heat pump. The pump is supplied with defrost functions which can be set by the installer. In the event of any problems, these may need adjusting. Contact your dealer.

27

Maintenance

Note

The particle filter is installed on the return pipe.

Optima 1400-1700

Optima 600-1100

Clean the dirt from the coil fins using a

degreasing agent and water.

Warning

During fan defrost, ice can detach from the fan grille and be thrown at high velocity. Do not stand too close and do not look directly into the fan during defrost.

Page 26 Page 28
Image 27
Page 26 Page 28
Contents IVT Optima Page Page Innehåll Important information For the userHow a heat pump works Technology in and around the heat pumpHeat pump collects heat from the outdoor air How a heat pump works IVT Optima Component parts of the heat pumpComponent parts of the heat pump Hot water is given priority over heating water Control unit RegoAutomatic defrosting Additional heat gives more outputOptima Control unit’s operating modesHeat pump with electric cassette Heat pump with electric boiler 290 A/WControl with an outdoor sensor and a room sensor Control with an outdoor sensorControl panel Status lamp290 A/W Control cabinet Menu dial Power switch ON/OFFHow to use the control panel Symbol overviewMenu levels MenuMenu overview Extra hot water Setting the heating, room sensor not installedSetting the heating, room sensor installed Set the heatingHot water sensor T3 TemperaturesFlow sensor T1 Outdoor sensor T2Overview Advanced menuHeat curve Flow temperatureOutdoor temperature Adjusting a single valueSet the heat curve Time control Set the desired room temperatureTime limited settings HysteresisHeating season Heating, maximum operating time at hot water requirementHoliday Hot water peak Hot water settingsRecurring increase in the hot water temperature Extra hot waterSetting the clock TimersDeactivate alarm buzzer Alarm logAccess level Return to factory settingsProtective covers MaintenanceUnscrew the protective covers Remove dirt and leavesParticle filter EvaporatorSnow and ice Emergency operation What to do if a fault occursExample of an alarm Dimmed menu displayList of all warning windows All alarms and warning windowsList of all alarms Tripped low pressure switchSensor failure / short circuit Tripped high pressure switchFaulty function in 4-way valve T6 High hot gas temperatureT8 High flow temperature Tripped motor cut-out compressor Low temperature in condenserPossible cause 3 Faulty heat carrier pump Possible cause 4 Compressor errorTripped motor cut-out fan Optima1000/1300 High temperature difference heat transfer fluidPossible cause 4 Faulty fan motor Possible cause 2 The hot water temperature is set too highAction Open the valves Technical information Factory settingsSound levels Technical informationSensor table Temperature ºC

600 - 1700 specifications

The Optima Company 600 - 1700 is a sophisticated product line designed to meet the demanding needs of modern industrial applications. Recognized for its efficiency and versatility, the Optima 600 - 1700 series has gained traction across various sectors, including manufacturing, chemical processing, and energy production.

At its core, the Optima 600 - 1700 combines cutting-edge technology with user-friendly features. One of the standout characteristics of this series is its advanced control system. The intuitive interface allows operators to easily configure settings, monitor performance, and receive real-time updates on system conditions. This feature not only enhances user experience but also maximizes operational efficiency by minimizing downtime.

A notable aspect of the Optima series is its modular design, which offers a high degree of customization. Businesses can choose from various configurations and components that best suit their specific operational needs. This adaptability means that the Optima 600 - 1700 can be scaled up or down, making it ideal for both small-scale operations and large production facilities.

The durability of the Optima 600 - 1700 is another key feature. Designed to withstand harsh industrial environments, the materials used in its construction ensure longevity and reliability. Manufacturers have prioritized robust engineering, resulting in a product that requires minimal maintenance while consistently delivering optimal performance.

Energy efficiency is a critical focus for the Optima Company, and the 600 - 1700 series exemplifies this commitment. The equipment is designed to minimize energy consumption without sacrificing functionality. This not only reduces operational costs for businesses but also aligns with global sustainability goals.

Further enhancing its capabilities, the Optima 600 - 1700 series incorporates smart technology features. With integrated IoT functionalities, clients can benefit from predictive maintenance, enabling them to anticipate potential issues before they escalate. This proactive approach to maintenance leads to increased uptime and can result in substantial cost savings over the lifespan of the equipment.

In summary, the Optima Company 600 - 1700 series stands out as a remarkable solution in the industrial equipment market. With its combination of advanced technology, customization options, durability, energy efficiency, and smart features, it meets the evolving demands of businesses while ensuring reliability and performance. Manufacturers and industrial operators looking for an advanced yet practical solution would do well to consider the Optima 600 - 1700 series as a key asset in their operational arsenal.
Top Page Image Contents