GE ASQ28 Storm Window Requirements, Prepare the Window, Remove the Front Grille if Attached

Page 9

Window Installation Instructions

1WINDOW REQUIREMENTS

•These instructions are for a standard double-hung window. You will need to modify them for other types of windows.

•All supporting parts must be secured to firm wood, masonry or metal.

•The electrical outlet must be within reach of the power cord.

181⁄2″ min.

30″ to 40″

(With accordion panels)

2STORM WINDOW REQUIREMENTS

A storm window frame will not allow the air conditioner to tilt toward the outside, and will keep it from draining properly.

To adjust for this, attach a piece of wood to the sill.

WOOD PIECES –

WIDTH: 2″

LENGTH: Long enough to fit inside the window frame.

THICKNESS: To determine the thickness, place a piece of wood on the sill to make it 1/2″ higher than the top of the storm window frame or the vinyl frame.

Attach securely with nails or screws provided by the installer.

3PREPARE THE WINDOW

Cut the window sash seal to the proper length. Peel off the backing and attach the seal to the underside of the window sash.

4REMOVE THE FRONT GRILLE (IF ATTACHED)

AOpen the inlet grille

downward by pulling out the upper corners of the inlet grille.

Lift it up and off.

BGrasp the filter

at the top center and pull it out.

CRemove the screw

from the grille.

DGently but firmly grasp

1/2″ higher than storm window frame

Storm window frame

1/2″ higher

than vinyl frame (on some windows)

Wood

Sill

Vinyl frame

the lower grille corners,

press in on the case sides and pull forward to release.

NOTE: Do not pull the bottom edge toward you more than 3″ or you

may damage the tabs of the grille.

ELift the grille up and off the top tabs.

9

Image 9

Contents Write the model and serial numbers here Model # Serial # Air ConditionersDo not use an adapter plug with this appliance Safety PrecautionsGe.com USE of Extension CORDS-115-Volt models onlyAbout the controls on the air conditioner Remote ControlCool Mode Power Outage Recovery FeatureFan Mode Vent ControlHow to Insert the Batteries Care and cleaning of the air conditionerGrille and Case Outdoor CoilsBefore YOU Begin Electrical RequirementsTools YOU will Need Parts Included Window Installation InstructionsStorm Window Requirements Window RequirementsPrepare the Window Remove the Front Grille if AttachedPrepare the Case Remove the AIR Conditioner from the CaseInstall the Case in the Window Install the CaseInstall the AIR Conditioner in the Case Install the Security Bracket and the Foam TOP Window GasketFinish the Wall Opening Through-the-Wall Installation Instructions-OptionalNormal Operating Sounds Troubleshooting Tips…General Electric Company Consumer Product Ownership Registration GE Air Conditioner Warranty What Is Not CoveredGE Will Replace Parts and Accessories Schedule ServiceConsumer Support GE Appliances Website Real Life Design StudioAcondicionadores de Aire Instrucciones de Seguridad Instrucciones ¡ADVERTENCIAControl remoto Acerca de los controles en el acondicionador de aireModo Cool Frio Función de recuperación de pérdida de energíaModo de FAN Ventilador Control de la ventilaciónPrecaución no Opere el Cuidado y limpieza del acondicionador de aireRequisitos Electricos Antes DE IniciarPartes Incluidas Herramientas QUE Usted NecesitaráRequisitos DE UNA Ventana DE Tormentas Requisitos Para LA VentanaPrepare LA Ventana Retire LA Parrilla Frontal SI Está PegadaRetire EL Acondicionador DE Aire DE LA Caja Prepare LA CajaInstale LA Caja Instale LA Caja EN LA VentanaInstale EL Acondicionador DE Aire EN LA Caja DE LA VentanaImportante Instrucciones de instalación a través de la pared-opcionalTermine LA Abertura EN LA Pared Solucionar problemas Sonidos de operación normales GE reemplazará Garantía de su acondicionador de aire de GELo que no está cubierto Un añoSolicite una reparación Apoyo al Consumidor Página Web de GE AppliancesGarantías ampliadas Piezas y accesorios