Heatiator ECO-ADV-WS22 warranty H.Burn Rate Air Control, I. Burn Rates and Operating Efficiency

Page 10
H.Burn Rate Air Control

H.Burn Rate Air Control

The air supply enters at the upper front of the firebox, near the top of the glass door.

This preheated air supplies the necessary fresh oxygen to mix with the unburned gases, helping to create sec- ond, third and fourth combustions

This air is regulated by the Burn Rate Air Control.

There are four settings High, Medium-High, Medium-Low and Low.

When the control is raised all the way up it is on the High setting and when pushed all the down it is on the Low setting. Figure 11.1 on page 11.

High

High

Medium

 

Medium

 

Low

 

Figure 10.1 - Burn Rate Air Control

I. Burn Rates and Operating Efficiency

For maximum operating efficiency

1.Follow the instructions below for each burn rate for the Burn Rate Air Control. Figure 10.1.

2.Burn dry, well-seasoned wood.

Burn Rates

1. Starting a Fire

Open the Burn Rate Air Control by raising it all the way to the top for the High setting.

The blower tends to cool the appliance. Leave the blower off until the burn is well established, i.e., 30 minutes.

After loading the appliance with wood and starting the fire, set the Burn Rate Air Controls to the desired setting by following the burn rate instructions below.

2. High Burn Rate - Maximum Heat* - 30,000+ BTU/hr

Raise the Burn Rate Air Control all the way up until it stops (top marker) to a fully open position.

Be sure and monitor the fire closely while in this setting to avoid overfiring your stove.

3.Medium-High Burn Rate* - 15,000 to 30,000 BTU/hr

Raise the Burn Rate Air Control to the Medium High marker. Blower may remain on.

4.Medium-Low Burn Rate* - 10,000 to 15,000 BTU/hr

Raise the Burn Rate Air Control to the Medium marker. Leave the blower off until the burn is well established, i.e., 30 minutes.

5.Low Burn Rate* - Below 10,000 BTU/hr

Leave the Burn Rate Air Control at the bottom marker. Leave the blower off until the burn is well established, i.e., 30 minutes.

*NOTE: These are approximate settings, and will vary with type of wood or chimney draft. Due to altitude and other environmental circumstances, this operational information is a guideline only.

10

Heatilator • ECO-ADV-WS227057-128C • August 13, 2010

Image 10
Contents WS22 DO DIS NOT C AR DModel ECO-ADV-WS22 Wood Burning Stove LOCATION Back of Appliance SAMPLE OF SERIAL NUMBER / SAFETY LABELCongratulations Test Lab andSafety Alert Key TABLE OF CONTENTSInstaller’s Guide User’s GuideWARRANTY COVERAGE Warranty PolicyHEATILATOR ECO-CHOICEWARRANTY WARRANTY PERIODWARRANTY COVERAGE WARRANTY EXCLUSIONSThis warranty is void if WARRANTY EXCLUSIONS1 Listing and Code Approvals D. BTU & Efficiency SpecificationsC. Glass Specifications A. Appliance CertificationA. Your Wood Appliance - General Operating Parts User Guide2 Operating Instructions Hot glass will cause burnsC. Overfiring B. Fire SafetyD. Combustible/Non-combustibleMaterials E. Seasoned Wood2. Second Stage G. Burning Process1. Kindling or First Stage 3. Final StageFigure 10.1 - Burn Rate Air Control H.Burn Rate Air ControlI. Burn Rates and Operating Efficiency For maximum operating efficiencyBack of Firebox J. Correct Baffle & Blanket PlacementCeramic Blanket Baffle BoardK. Building A Fire Do NOTSoft woods L.Wood FuelWARNING! Risk of Fire Hard woodsFigure 14.2 - Snap Disc Location M. Blower Operating InstructionsN. Clear Space 7.Snap Disc LocationSOLUTIONS P. Frequently Asked QuestionsISSUES O. Opacity SmokeLOAD WOOD The stove is ready for normal operationQ. Quick Start Guide ADD NEWSPAPERC. Appliance Inspection - Routine 3 Maintenance and ServiceA. Disposal of Ashes WARNING! Risk of FireE. Firebrick Inspection D. Glass CleaningFrequency As desired F. Quick Reference Maintenance Guide Solution 4 Troubleshooting GuideStart Fire Problems Possible CauseB. Snap Disc Replacement 5 Service Parts ReplacementA. Glass Replacement WARNING! Risk of Fire or InjuryC.Baffle Removal Figure Figure 22.1 - BaffleD. Door Handle Assembly Replacing Tube Channel Assembly E. Tube Channel Assembly ReplacementRemoving Tube Channel Assembly NOTE Service Space6 Getting Started Installer’s GuideA. Design and Installation Considerations B. DraftD. Locating Your Stove & Chimney E. Chimney Termination RequirementsF. 2-10-3Rule Flat RoofI.Inspect Appliance and Components H. Fire SafetyG. Tools And Supplies Needed WARNING! Risk of FireFigure 29.1 - Front View 7 Dimensions and ClearancesA. Appliance Dimensions Figure 29.2 -TopViewB. Clearances to Combustibles UL and ULC SEE PIPE MANUFACTURERS CLEARANCES - NOT TESTEDFLOOR PROTECTION C. Hearth Protection RequirementsCANADA See FigureConverting k to R Thermal Conductivity k valueThermal Resistance R value Converting R to kB. Inspections 8 Venting and Chimney SystemsA. Venting Systems C. Larger ChimneysS629M, STANDARD FOR 650oC FACTORY-BUILTCHIMNEYS E. Chimney Height / Rise and RunF.Factory-BuiltChimney WARNING! Risk of FireG. Masonry Chimney H. Masonry Chimney Liner Solid Pack Chimney with Metal Supports I.Air ClearancesJ. Thimble as a ThimbleWARNING! Risk of Fire as a Thimble Cont’dSolid Pack Chimney with Metal Supports Heatilator ECO-ADV-WS22 7057-128C AugustItems Needed for Installation not supplied A. Outside Air Kit Installation9 Appliance Set-up Figure 39.2 - Alternate Floor InstallationB. Mobile Home Installation WARNING! Risk of AsphyxiationD. Adjusting the Blower Speed Control C. Blower Installation OptionalCAUTION! Risk of Shock Reference Materials 13 Inlet Assembly14 Door Assembly A. Exploded ViewHOW TO ORDER Brick AssemblyB. Service Parts & Accessories DESCRIPTIONAccessories B. Service Parts & Accessories Cont’dHOW TO ORDER DESCRIPTIONDescription of Service C. Service And Maintenance LogDate of Service Performed ByDescription of Service C. Service And Maintenance Log Cont’dDate of Service Performed ByD.Homeowner’s Notes Heatilator ECO-ADV-WS22 7057-128C AugustColville, WA Division of HNI INDUSTRIES E. Contact InformationHearth & Home Technologies 1445 North Highway DO DIS NOT C AR D