Heatiator ECO-ADV-WS22 Maintenance and Service, A. Disposal of Ashes, WARNING! Risk of Fire

Page 17
3 Maintenance and Service

3 Maintenance and Service

A. Disposal of Ashes

Frequency: When ash is within 1-3/4 inch (44mm) of firebox lip. Leave 1/4 to 1/2 inch (6-13mm) of ash in the bottom of the firebox.

By: Homeowner

WARNING! Risk of Fire! Ashes could contain hot embers.

Place ashes in a metal container with a tight-fitting lid.

The closed container should be placed on a non- combustible floor or on the ground, well away from all combustible materials, pending final disposal.

If the ashes are disposed of by burial in soil or otherwise locally dispersed, they should be retained in the closed container until all cinders have thoroughly cooled

B.Chimney and Chimney Connector Inspection/Cleaning

Frequency: Every 2 months during heating season or as recommended by a certified chimney sweep; more frequently if chimney exceeds or is under 14-16 ft (4.3- 4.8m). (measured from bottom of appliance).

By: Certified Chimney Sweep

WARNING! Risk of Fire! Ignited creosote is extremely HOT. Prevent creosote buildup.

Remove all ash from the firebox and extinguish all hot embers before disposal.

Allow the appliance to cool completely.

Disconnect flue pipe or remove baffle and ceramic blanket from appliance before cleaning chimney. Otherwise residue can pile up on top of the baffle and ceramic blanket. (See Baffle Removal on page 22).

Close the door tightly.

The creosote or soot should be removed with a brush specifically designed for the type of chimney in use.

Clean out fallen ashes from the firebox.

It is also recommended that before each heating season the entire system be professionally inspected, cleaned and repaired if necessary.

WARNING! Risk of Fire!

Do not use chimney cleaners or flame colorants in your appliance. It will corrode your pipe.

Creosote - Formation and Need for Removal

When wood is burned slowly, it produces tar and other organic vapors, which combine with expelled moisture to form creosote.

The creosote vapors condense in the relatively cool chimney flue of a slow-burning fire.

As a result, creosote residue accumulates on the flue lining. When ignited this creosote makes an extremely hot fire.

The chimney and chimney connector shall be inspected every two months during the heating season to determine when a creosote buildup has occurred.

When creosote has accumulated it shall be removed to reduce the risk of a chimney fire.

C. Appliance Inspection - Routine

Frequency: Every 2 months at the same time the chim- ney and chimney connector are inspected.

By: Homeowner

Check for:

Cracks in glass

Door handle - smooth cam operation

Baffle and ceramic blanket correct placement

Baffle for cracks

Firebrick for cracks, broken or crumbly

Door gasket. (Dollar bill test). Place a dollar bill between the stove and the door and then shut the door. If you can pull the dollar bill out, remove one spacing washer from the door handle behind the latch cam and try the test again. If you can still pull the dollar bill out, replace the door gasket.

Glass frame for loose screws

Heatilator • ECO-ADV-WS227057-128C • August 13, 2010

17

Image 17
Contents Model ECO-ADV-WS22 Wood Burning Stove DO DIS NOT C AR DWS22 Congratulations SAMPLE OF SERIAL NUMBER / SAFETY LABELLOCATION Back of Appliance Test Lab andInstaller’s Guide TABLE OF CONTENTSSafety Alert Key User’s GuideHEATILATOR ECO-CHOICEWARRANTY Warranty PolicyWARRANTY COVERAGE WARRANTY PERIODThis warranty is void if WARRANTY EXCLUSIONSWARRANTY COVERAGE WARRANTY EXCLUSIONSC. Glass Specifications D. BTU & Efficiency Specifications1 Listing and Code Approvals A. Appliance Certification2 Operating Instructions User GuideA. Your Wood Appliance - General Operating Parts Hot glass will cause burnsD. Combustible/Non-combustibleMaterials B. Fire SafetyC. Overfiring E. Seasoned Wood1. Kindling or First Stage G. Burning Process2. Second Stage 3. Final StageI. Burn Rates and Operating Efficiency H.Burn Rate Air ControlFigure 10.1 - Burn Rate Air Control For maximum operating efficiencyCeramic Blanket J. Correct Baffle & Blanket PlacementBack of Firebox Baffle BoardDo NOT K. Building A FireWARNING! Risk of Fire L.Wood FuelSoft woods Hard woodsN. Clear Space M. Blower Operating InstructionsFigure 14.2 - Snap Disc Location 7.Snap Disc LocationISSUES P. Frequently Asked QuestionsSOLUTIONS O. Opacity SmokeQ. Quick Start Guide The stove is ready for normal operationLOAD WOOD ADD NEWSPAPERA. Disposal of Ashes 3 Maintenance and ServiceC. Appliance Inspection - Routine WARNING! Risk of FireFrequency As desired D. Glass CleaningE. Firebrick Inspection F. Quick Reference Maintenance Guide Start Fire Problems 4 Troubleshooting GuideSolution Possible CauseA. Glass Replacement 5 Service Parts ReplacementB. Snap Disc Replacement WARNING! Risk of Fire or InjuryFigure Figure 22.1 - Baffle C.Baffle RemovalD. Door Handle Assembly Removing Tube Channel Assembly E. Tube Channel Assembly ReplacementReplacing Tube Channel Assembly NOTE Service SpaceA. Design and Installation Considerations Installer’s Guide6 Getting Started B. DraftE. Chimney Termination Requirements D. Locating Your Stove & ChimneyFlat Roof F. 2-10-3RuleG. Tools And Supplies Needed H. Fire SafetyI.Inspect Appliance and Components WARNING! Risk of FireA. Appliance Dimensions 7 Dimensions and ClearancesFigure 29.1 - Front View Figure 29.2 -TopViewSEE PIPE MANUFACTURERS CLEARANCES - NOT TESTED B. Clearances to Combustibles UL and ULCCANADA C. Hearth Protection RequirementsFLOOR PROTECTION See FigureThermal Resistance R value Thermal Conductivity k valueConverting k to R Converting R to kA. Venting Systems 8 Venting and Chimney SystemsB. Inspections C. Larger ChimneysF.Factory-BuiltChimney E. Chimney Height / Rise and RunS629M, STANDARD FOR 650oC FACTORY-BUILTCHIMNEYS WARNING! Risk of FireG. Masonry Chimney H. Masonry Chimney Liner J. Thimble I.Air ClearancesSolid Pack Chimney with Metal Supports as a ThimbleSolid Pack Chimney with Metal Supports as a Thimble Cont’dWARNING! Risk of Fire Heatilator ECO-ADV-WS22 7057-128C August9 Appliance Set-up A. Outside Air Kit InstallationItems Needed for Installation not supplied Figure 39.2 - Alternate Floor InstallationWARNING! Risk of Asphyxiation B. Mobile Home InstallationCAUTION! Risk of Shock C. Blower Installation OptionalD. Adjusting the Blower Speed Control 14 Door Assembly 13 Inlet AssemblyReference Materials A. Exploded ViewB. Service Parts & Accessories Brick AssemblyHOW TO ORDER DESCRIPTIONHOW TO ORDER B. Service Parts & Accessories Cont’dAccessories DESCRIPTIONDate of Service C. Service And Maintenance LogDescription of Service Performed ByDate of Service C. Service And Maintenance Log Cont’dDescription of Service Performed ByHeatilator ECO-ADV-WS22 7057-128C August D.Homeowner’s NotesHearth & Home Technologies 1445 North Highway E. Contact InformationColville, WA Division of HNI INDUSTRIES DO DIS NOT C AR D