Heath Zenith 598-1347-00 Installation, White, Gasket Mounting Bolt, Wiring Floodlight

Page 7

WARNING: Turn power off at the fuse or circuit breaker.

Installation

1.Remove the existing light fixture.

2.Install the mounting strap as shown using two screws that fit your junction box.

Note: The plastic hanger can be used to hold the fixture while wiring. Thread the small end of the plastic hanger through the hole in the center of the cover plate. Insert the small end into one of the slots on the mounting strap.

3.Set the LAMP MODE switch to the desired light turn-on effect (Normal, Soft, Flash).

4.Route the wires from the light receiver through the large gasket holes.

5.Twist the junction box wires and fixture wires together as shown.

Secure with UL approved wire connectors.

6.Align the cover plate and cover plate gasket. Secure with mounting bolt.

7.Push the rubber plug firmly into place.

8.Not intended for waterproof junction boxes. Fixture should be surface mount only. Caulk the wall plate mounting surface with silicone weather sealant.

9.Adjust the lamp holders by loosening the lock nuts. Note: Do not rotate the lamp holders more than 180° from the factory setting.

Caution: To avoid water damage and electrical shock, keep lamp holders 30° below horizontal.

10.Screw incandescent bulb up to rated wattage into module. When screwing in the lamps, do not overtighten.

Caution: Do not exceed the maximum load limits listed above.

11.Check operation. Activate transmitter being used with receiver (see transmitter instructions).Asignal will be sent to the receiver to turn the receiver ON or OFF.

WARNING: Risk of fire. Do not aim the lamps at a combustible surface within 3 ft. (1 m).

Mounting

White to

 

Black to

Rubber

Strap

 

White

 

Black

 

 

Plug

 

 

 

 

 

 

 

 

Gasket Mounting

Bolt

Junction box ground wire to green

ground screw on fixture.

Wiring Floodlight

ENGLISH

598-1347-00

Image 7
Contents Example 2 Code Settings, System FeaturesCode Settings Example 1 Code Settings, SystemCode Code Switch LocationsCode Switches Motion Sensor240 Motion Sensors Select Night or 24 Hour ModeInstalling Batteries Installing Motion SensorMotion Sensor Only Check Operation and AdjustmentDualBrite Dimmer Control Motion Sensor ControlsMotion Sensor Coverage Area 180 Motion Sensor240 Halogen FloodLight Bulb Installation and ReplacementReceiver Information Indoor Plug-In ConverterWhite InstallationJunction box ground wire to green Ground screw on fixture Wiring FloodlightPAR Floodlight Regulatory Information Troubleshooting GuideTechnical Service No Service Parts Available for this ProductTWO Year Limited Warranty Grupo a Grupo B Indica la posición del interruptor Calibraciones DEL CódigoEjemplo 1 Calibraciones del código, sistema Calibración de fábricaConvertidor enchufable para usarse bajo techo Ubicaciones DE LOS Interruptores DE Circuito ImpresoInterruptores De circuito Impreso Detector de movimiento deInstalación del Detector de Movimiento Detectores DE Movimiento DE 180 YSeleccione modo nocturno o modo de 24 horas Instalación de las bateríasSólo Detector de Movimiento de Revisión de la operación y de la regulaciónControl DualBrite de reducción de intensidad Controles del Detector de Movimiento deSensibilidad del Detector de Movimiento 180Área de Cobertura del Detector de Movimiento de MovimientoMovimientoInstalación y Cambio de la Bombilla Información DEL ReceptorConvertidor enchufable para Usarse bajo techo Faro halógenoCableado del reflector InstalacionFaro Par No hay piezas de servicio disponibles para este producto Guía de Análisis de AveríasServicio Técnico Información RegulatoriaGarantía Limitada a 2 Años Exemple 2 Réglage des codes, système CaractéristiquesRéglage DES Codes Du guide de référenceDétecteur de mouvement sur Emplacement DES MICRO-INTERRUPTEURSConvertisseur enfichable intérieur Détecteurs DE Mouvement SUR 180 ET Installation Du Détecteur De MouvementSélection du mode de nuit ou du mode 24 heures Installation des pilesDétecteur de mouvement sur 240 seulement Commandes du détecteur de mouvement surVérification du fonctionnement et du réglage Gradateur DualBriteMDRéglage de la couverture du détecteur de mouvement Zone de couverture du détecteur de mouvement surMouvementMouvement DétecteurDétecteur Sensibilité du détecteur de mouvementConvertisseur enfichable intérieur Installation et Remplacement de la LampeEmplacements des commandes Informations SUR LE RécepteurBlanc Blanc à Noir à noirCâblage du projecteur Projecteur PAR Aucune pièce de rechange n’est disponible pour ce produit Service TechniqueGuide DE Dépannage Renseignements de règlementsGarantie Limitée DE 2 ANS Is nça fra 598-1347-00

598-1347-00 specifications

The Heath Zenith 598-1347-00 is a highly regarded outdoor motion-activated light fixture designed to enhance security and convenience around residential properties. This device combines practicality with advanced technology to address the needs of homeowners seeking efficient lighting solutions.

One of the main features of the Heath Zenith 598-1347-00 is its powerful motion sensor, which detects movement within a specified range. The sensor has an adjustable sensitivity setting, allowing users to tailor its responsiveness to their specific environment. This means the light will activate when it detects motion within its coverage area, which significantly improves security by illuminating the surroundings when unexpected movement occurs.

The fixture is also equipped with a state-of-the-art LED light source. LEDs are known for their energy efficiency, consuming less power while providing bright illumination. This characteristic not only reduces electricity bills but also contributes to the longevity of the light fixture itself, as LEDs typically last significantly longer than traditional bulbs. The Heath Zenith 598-1347-00 can provide up to 1200 lumens of brightness, ensuring a well-lit area for enhanced visibility at night.

In terms of design, the Heath Zenith 598-1347-00 boasts a rugged and weather-resistant construction, making it suitable for various outdoor settings. It is designed to withstand the elements, with a durable housing that protects the internal components from moisture and corrosion. This ensures the fixture will maintain its functionality over time, regardless of the weather conditions it faces.

Another notable characteristic of this outdoor light is the adjustable timer and photocell feature. The timer allows homeowners to set how long the light will remain illuminated upon detecting motion, adding an extra layer of convenience. Meanwhile, the integrated photocell ensures the light only activates at night or in low-light conditions, further optimizing energy usage.

Furthermore, installation of the Heath Zenith 598-1347-00 is user-friendly, allowing homeowners to set it up with minimal hassle. The comprehensive mounting guide included makes it accessible for DIY enthusiasts and professional electricians alike.

In conclusion, the Heath Zenith 598-1347-00 is an excellent choice for those seeking an effective outdoor lighting solution. With its powerful motion detection, energy-efficient LED technology, durable design, and user-friendly features, it serves as a practical addition to any home, enhancing both security and convenience.