INSTALLATION INSTRUCTIONS
4.Fitting an optional flue Gather
4.1Fitting Of Optional Flue Gather
| 16" | 22" | 24" | 26" | 28" |
|
|
|
|
|
|
Flue gather - | - | 8658 | 8659 | 8660 | 8661 |
standard (central) |
|
|
|
|
|
|
|
|
|
|
|
Flue gather - | - | 8663 | 8664 | 8665 | 8662 |
staggered (offset) |
|
|
|
|
|
|
|
|
|
|
|
•Place the appropriate flue gather on top of the convector box, See Diagram 27
27
Return
Flange
Back of 
convector
box
PR8093
•Line the inside of the return flange up with the back of the convector box
•Mark the hole positions on the top of the Convector box
•Drill appropriate holes for a self tapping screw/tapping a hole
•Secure the gather to the top using chosen fixings (not supplied)
•Ensure a good seal is achieved with the top of the box by using either ladder tape or fire cement
5.Installing Solid fuel cast iron Convector
Installation of the fireplace must comply with Building Regulations relating to heat producing appliances (Approved Document number J1/2/3). If there is any conflict between these instructions and the Regulations, the Regulations shall apply.
5.1After installing the firebox, Diagram 28
•Ensure the flange of the firebox is appropriately sealed to the wall
•Slide the 2 ceramic tile sets into the ladders on either side of the cast iron fireplace (B)
•Secure in place with screws and flat bars provided
Caution: Do not overtighten the bars as this may crack the tiles.
•Attach the fireplace hood (C) using the threaded studs and nuts fixed to it
•Apply a continuous band of sealant to the hatched area on the front of the firebox, see Diagram 28
28 |
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
| C |
| ||
|
| A |
|
|
|
|
| |||
|
|
| B |
| ||||||
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
| F |
|
|
|
|
|
|
|
| H |
| ||
|
|
|
|
|
|
|
|
|
| ||||||||
|
|
|
|
|
|
| D |
|
|
|
|
| |||||
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
| ||
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
| ||
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
| G |
|
|
|
|
|
|
|
|
|
| ||
E |
|
|
|
|
|
|
|
|
|
|
| I | |||||
|
|
|
|
|
|
|
|
|
|
|
|
|
| ||||
|
|
|
|
|
|
|
|
|
|
|
| ||||||
•Lift the cast iron fireplace into position against the front of the firebox
•Secure it loosely with the nuts and bolts provided through the two holes (D) below the hood
•Secure the bottom of the fireplace to the firebox using the
2 bolts and brackets supplied, See Diagram 29
29
•Tighten all 4 bolts securely and wipe off surplus sealant
•Slide the base plate (E) into the bottom of the firebox, slotting it over the lugs on the cast iron fireplace
•Stand the grate (F) on the base plate so it fits tightly against the back and sides of the firebox
24