Samsung N640CJ2024/EHQ, N640CP4007/SEF, N640CP4024/EHQ, N640CP2006/SEF, N640GP4001/SEF Security Menu

Page 55

When the Infrared port field is set to Enabled, the computer’s operating system uses the default configuration or the configuration you choose. If you select Disabled, you free up an IRQ for use by another device.

Parallel port: Configures the parallel port. The options for this field are Enabled (default), or Disabled. If you set this field to Enabled, you can set the Mode field and the Base I/O Address field. Settings for the Base I/O Address are 378 IRQ7(default), 378 IRQ5, 278 IRQ7, 278 IRO5, 3BC IRQ7, and 3BC IRQ5. Settings for the Mode are Output only, Bi-directional, EPP (enhanced parallel port), and ECP (extended capabilities port). Selecting the ECP setting enables you to set the DMA Channel to 1, 2, or 3.

When the Parallel port field is set to Enabled, the computer’s operating system uses the default configuration or the configuration you choose. If you select Disabled, you free up an IRQ for use by another device.

Floppy disk controller: Configures the floppy disk controller. The options for this field are Enabled (default), or Disabled. When the Floppy disk controller field is set to Enabled, the computer’s operating system uses the default configuration for the controller.

Local Bus IDE adapter: Enables the integrated IDE local bus adapters. Options are Enabled (default) and Disabled.

Large Disk Access Mode: Enables your computer’s operating system to work with drives larger than 540 MB. Choose DOS (default) for Microsoft operating systems. Choose Other for any other operating systems.

Security Menu

Selecting Security from the menu bar displays the Security menu. Your computer’s advanced security system allows you to set two different passwords to prevent unauthorized access to system resources, data, and System Setup. From the Security menu, you can enable a boot password, disk access, a system backup reminder, and a virus check reminder.

Set User Password: Enables you to set a user password to control access to the system at boot. See ”Creating a Password” on page 60 for instructions on setting a password.The user password allows restricted access to the System Setup Security menu; the user has access only to changing his own password and to enabling or disabling Password on boot. A supervisor password must be set before a user password can be set

Using System Setup 55

Page 54 Page 56
Image 55
Page 54 Page 56
Contents Special Features of the User’s Manual Using Your DocumentationUsing the Software User Documentation LCD Introducing Your ComputerBack View of Computer Attaching the AC Adapter Using Your Computer for the First TimeTurning On the Computer Turning On the Computer’s PowerTurning Off Your Computer Adjusting the LCD DisplayAPMAdvanced Power Management mode Understanding PostRestarting Your Computer ACPIAdvanced Configuration and Power Interface modeTips for Using Your Computer Traveling with Your Computer Storing the Computer for Long Periods Handling SpillsKeyboard Using the KeyboardNumeric Keypad Using the Embeded Numeric KeypadDescription of Special Function Keys Using Special Function KeysFn Key Function Combination Using the Keyboard Using the Touchpad Using the TouchpadMouse Action How To Using the Touchpad System Status Lights Reading the System Status LightsReading the System Status Lights Peripheral Connectors Connecting Peripheral DevicesIconConnector Connecting Peripheral DevicesConnecting Peripheral Devices To remove a device from the Flex-Bay Using the Flex-BaySetting the IDE type Drive SwitchRemoving a Device from the Flex-Bay To install a device in the Flex-BayMagnetic fields can destroy the information on a disk Using the Floppy DriveUsing the Floppy Drive Using the CD-ROM Drive Using the CD-ROM DriveUsing the CD-ROM Drive Installing the Power DVD Player MPEG-2 Software Using the DVD-ROM DriveRemoving the Hard Drive Using the Hard DriveRemoving the Hard Drive Installing a Hard DriveCharging the Battery Using the BatteryRemoving the Battery Safely Using the BatteryRemoving the Battery Pack Installing the BatteryUsing the Battery Gauge Monitoring the Battery ChargeSet options under Battery Status and Alarm Settings Using PowerProfiler to Monitor the BatteryBattery Warnings Battery WarningsCondition Action to Take Sens Modem Naming Convention Using the ModemIf you use a simple terminal program Precautions before useIf you use a Windows Communication Program Description of 56K SpecificationInstall the Modem Driver Installing the Modem Driver in Windows MeSelecting a Country Confirming Installation of the Modem DriverDeleting the Modem Driver Installing the Modem Driver in Windows 95/98 Check if Country is selected correctly Command mode Modem CommandsWhat are AT commands? Before Using AT CommandsUsing Command Mode during Communications Using AT commandsDisplay the result value ATO Basic AT CommandsATS0? Menu Function Using System SetupStarting System Setup System Setup MenusNavigation Alternate Function Key System Setup Navigation KeysMain Menu Using System Setup Using System Setup Advanced Menu Security Menu Power Menu Using System Setup Exit Menu Boot MenuUsing System Setup System Passwords Using System SecurityCreating a Password Deleting a Password Locking the Hard Drive Boot Sector Requiring a Boot PasswordLocking the Keyboard Maximum Power Saving Mode Using Power Management OptionsRest Mode Standby ModeRest Mode Precautions Using PowerProfiler To create Fdisk Creating a Save to Disk PartitionTo create Phdisk Insert the System Recovery CD-ROM To reinstall your operating systemTo reinstall your original applications and drivers Resolution and Color Depth Video Features and ConfigurationSelecting a Monitor Type Configuring Display FeaturesVideo Driver Capabilities Changing Color Depth and Resolution Changing the Video Driver Using the TV-Out PortClick OK and follow the prompts that appear on the screen Setting Dual View mode Using Dual View modeLimits and cautions of using Dual View mode Three Displays Using several display devicesPrimary Limits Secondary Two DisplaysLimits on Video Driver while using Dual View mode Maintaining PC Cards Working with PC CardsWindows 98/ Me Using PC CardsWindows NT Working with PC Cards Battery Pack Using OptionsAC Adapter Memory Modules Auto AdapterInstalling a Memory Module Before You Install MemoryRemoving the Memory Module Compartment Door Hard Drives Installing a Memory ModuleCD-ROM Drive Setting the switch on 2nd HDDZIP Drive DVD-ROM Drive ModuleSuperdisk LS-120 Drive Inserting a 120MB LS-120 diskette into the LS-120 drive Docking OptionsIRQs About Drivers and System ResourcesDrivers IRQsService Pack 4 for Windows NT About Drivers and System Resources Computer is not behaving as expected TroubleshootingOperating Problem Computer does nothing when you turn it onPC Card does not work correctly Battery power seems to run out faster than expectedModem Problems Infrared ProblemsWhen using a PBX phone system I cant dial on my modem Troubleshooting Environment SpecificationsHardware Specifications DimensionNi-MH Dumb Battery Lithium-Ion Smart BatteryExternal AC Adapter CD-ROM AbbreviationsPcmcia Voltage collector current Universal serial busVolt Voltage alternating currentAC adapter BootBoot disk GlossaryCmos memory DMA direct memory accessCache memory CardBusIRQ interrupt request line Floppy diskHard drive AddressOperating system RAM random access memoryMBmegabyte MegabitSector ResolutionRefresh rate ROM read-only memoryDiskette a Recording the Computer Hardware ConfigurationDisabled Other Parallel port Enabled Mode Output onlyDisabled 42F8, IRQ 2E8, IRQ 3 Disabled Disabled Bi-directionalSecurity Menu Page Important Safety Instruction Iii Federal Communications Commission FCC Federal Communications Commission FCC Part 68 Statement Canadian Radio Interference Regulations CTR21 StatementClass 1 Laser Productlaserschutzklasse 1 Produkt Country Accredited Applicable Agency Power Cord RequirementCountry-Specific Power cord Set Requirements General RequirementsSEV
Related manuals
Manual 138 pages 1.75 Kb
Top Page Image Contents