Thomas & Betts UDAS, UDAP Burner Maintenance cont’d, Burner Orifice, Burner Removal cont’d

Page 30

27.Burner Maintenance (cont’d)

Burner Removal (cont’d)

Inspect and Clean the Burner

Re-Install the Burner

28.Burner Orifice

size. Each baffle is held in place by one screw. For re-assembly, on the

secondary air shield, mark the location (top and bottom) of each baffle.

Remove all baffles.

8.Remove Burner Assembly

a)Locate the burner body supports. Depending on the size, the burner will have two or more supports. At each support, remove the one screw that attaches it to the secondary air shield

b)Holding the venturi tube, slide the entire burner assembly slightly to the right to disengage the burner from the supports on the left. Then rotate the open end of the venturi tube inward toward the heater. Carefully pull the burner assembly out of the cabinet.

With the burner assembly removed, shine a flashlight on the burner ribbons. Look for carbon buildup, scale, dust, lint, and/or anything that might restrict flow through the spaces between the burner ribbons. Holding the burner assembly so that any foreign material will fall away from the burner, use a stiff bristle brush to loosen and remove any foreign material(s). If the burner is excessively dirty, remove one of the burner end caps. Remove the four screws that hold the end cap to the burner housing. Lightly tap the end cap to remove it.

Clean all foreign material from the burner and venturi. After the burner is thor- oughly clean, replace the end cap making certain that it is tight against the burner housing. NOTE: If any of the burner components are damaged or deteriorated, replace the burner assembly.

Inspect the Lower Portion of the Heat Exchanger (with burner assembly removed)

At the burner flame entrance of each tube, shine a bright light into each heat exchanger section. With the light shining into the heat exchanger, observe the outside for visible light. Repeat this procedure with each heat exchanger section. If any light is observed, replace the heat exchanger.

Instructions to Re-Install the Burner (Refer to FIGURE 17)

1.Attach the Burner Assembly - Holding the venturi tube, slide the entire burner assembly into position. Align the supports on the left side with the slots in the burner shield; sliding the supports into the slots. On the right, re- attach each burner body support to the secondary air shield.

2.Attach the Secondary Air Baffles (Sizes 60-400 only) - Re-attach the secondary air baffles as marked. Baffles may be different sizes and each must be attached in the correct location.

3.Attach the Control Assembly - Carefully slide the control assembly into position. Re-attach with the same screws. Check to be sure all wire connec- tions are secure.

4.Attach the Gas Train - Slide the gas train so that the orifice adapter is through the bracket. Fasten the gas train to the bracket with the locking nut. Install the gas orifice. Re-connect the wires to the gas valve.

5.Close the access panel.

6.Reconnect the gas supply at the union outside of the cabinet. Leak test the connection with leak detecting solution.

7.Turn on the electric and the gas. Check for proper operation.

Burner orifice usually only needs to be replaced when installing a gas conversion kit. If ordering a replacement orifice only, give BTUH content and specific grav- ity of gas, as well as the model and serial number of the unit. When removing or replacing the burner orifice be careful not to damage the venturi tube and/or the bracket.

Form RZ-NA I-UDA, P/N 195673 Rev 5, Page 30

Page 29 Page 31
Image 30
Page 29 Page 31
Contents Table of Contents Series Fan-Type Unit HeatersHazard Levels of Warnings in this Manual Installation CodesGeneral Venting Manual by ModelWarranty Uncrating and Preparation Massachusetts RequirementDimensions SizeModel Udas Separated Combustion Fan Technical Data Size 100 125High Altitude Operation Instructions for Changing Pressure SwitchPressure Switch ClearancesCombustion Air applies to Model Udap and Model Model Udap and Model UDAP-CVUnit Heater Location Heater ThrowLocation Recommendations Model Udap Size 100 125 150 175 225 250 300 350 400 Unit Heater Location cont’dHanging the Heater Model Udas Size 100 125 150 175 225 250 300 350 400Be sure Threaded swivel Connectors areRecommended maximum hanger rod length is 6 feet 1.8M Locked toGas Piping and Pressures Sizing Gas Supply LineGas Connection Size Instructions Instructions for High Altitude Derate Manifold Pressure Settings by Altitude for CanadaGas Piping and Pressures cont’d Two -Stage ValveHigh Altitude Capacity Changes Feet MetersBurner Electrical Supply and Connections Thermostat and ConnectionsCombustion Air Proving Switch Pressure Switch Pressure Switch Settings Combustion Air ProvingLimit Control Normal Heat Cycle Operating Sequence Door Switch Model Udas only Ignition SystemDip Switch StatusLED LightsIgnition System cont’d SW1 SW2 TimeContinuous Fan Operation Fault Modes Fault Modes cont’d Lockout Gas Valve Fan MotorWiring Diagrams Operating SequenceWiring Diagrams cont’d SW1 Check Installation and Startup Check the installation prior to startup Heater StartupOperating Instructions Operating Sequence Check installation after startup Vent System Testing Procedure Model UdapMaintenance Schedule Startup cont’dUse only factory-authorized parts Heat Exchanger Maintenance Burner Maintenance Burner Removal Instructions Refer to FigureInstructions to Re-Install the Burner Refer to Figure Burner Maintenance cont’dInspect and Clean the Burner Re-Install the Burner Burner OrificeDSI Cont’d IgnitionSystem Fan BladesOperating Gas Valve Combustion Air Pressure SwitchDoor Switch Udas onlyAir System Troubleshooting Flame Rollout Switch Sizes 30-125 onlySwitch DisconnectWill not start General TroubleshootingVenter motor Burner willTroubleshooting cont’d Cont’d

UDAP, UDAS specifications

Thomas & Betts is a well-respected name in the electrical and industrial products sector, known for its innovation and quality. Among its impressive portfolio, the UDAS and UDAP series of connectors stand out for their reliable performance and advanced features. These connectors are specifically designed to meet the rigorous demands of electrical applications in various industries.

The UDAS (Universal Disconnect Appliance Switch) and UDAP (Universal Disconnect Appliance Plug) are engineered for high-capacity applications where safety, efficiency, and ease of use are paramount. One of the main features of these connectors is their ability to deliver increased electrical resistance and durability. They are constructed from high-quality materials that can withstand extreme environmental conditions, making them ideal for outdoor and harsh industrial applications.

Another key technology employed in the UDAS and UDAP series is the quick-connect mechanism. This innovative design allows users to connect and disconnect circuits swiftly without requiring excessive force or complex tools. This is particularly beneficial in settings where downtime must be minimized and efficiency is crucial. Additionally, the connectors are designed to provide a secure, locking fit to ensure consistent electrical contact, thereby enhancing operational safety.

The UDAS and UDAP connectors are manufactured to comply with several industry standards, ensuring that they meet or exceed the requirements for electrical safety and performance. Their user-centric design features help in reducing installation time and costs, making them a preferred choice among contractors and engineers.

Furthermore, these connectors are versatile, compatible with a wide range of electrical systems, and can be employed in applications such as HVAC, lighting, and power distribution. They also come in various sizes and configurations to accommodate diverse specifications, improving customization options for different projects.

In summary, the Thomas & Betts UDAS and UDAP series stands out for their robust design, quick-connect technology, and versatility across various industrial applications. Their durability and compliance with safety standards make them an excellent choice for professionals seeking reliable connectivity solutions in demanding environments. Investing in these connectors ensures optimal performance and safety in electrical installations, showcasing Thomas & Betts' commitment to excellence in electrical components.
Top Page Image Contents