Heatiator ECO-WINS18 owner manual Metal Heat Circulating Masonry, Prefabricated Metal Chimney

Page 36

E. Metal Heat Circulating Masonry

This insert conforms with the safety standard UL-1482 and ULC S628 (Canada) in all respects and is approved to UL & ULC safety standards for installation and use within a fire- place with masonry chimney, in accordance with NFPA 211, and CAN/CSA-B365-01.

F. Prefabricated Metal Chimney

The chimney can be new or existing, masonry or prefabricated and must meet the following minimum requirements:

•Must be minimum 6 inch (152mm) inside diameter of high temperature chimney listed to UL 103 HT (2100oF) or ULC S628.

•Must use components required by the manufacturer for installation.

•Must maintain clearances required by the manufacturer for installation.

•Refer to manufacturers instructions for installation

•This insert is listed to UL 1482 Standard and is approved for installation into listed factory-built solid fuel fireplaces listed to UL 127 conforming to the follow- ing specifications and instructions:

•The original factory-built clearance fireplace chimney cap must be re-installed after installing the approved chimney liner meeting type UL 103 HT requirements (2100°F) per UL 1777.

•The liner must be securely attached to the insert flue collar and the chimney top.

•The air flow of the factory-built solid fuel fireplace system must not be altered. The flue liner top support attachment must not reduce the air flow for the existing air-cooled chimney system.

•No dilution air is allowed to enter the chimney.

1.Secure the fireplace damper in the open position. If this cannot be accomplished, it will be necessary to remove the damper.

2.Seal damper area of chimney around chimney connector with a high temperature sealant or seal insert against the face of the fireplace.

3.Both methods must be removable and replaceable for cleaning and re-installation.

 

Inches

Millimeters

Minimum Width of Cavity Opening - Front

24 1/2*

622*

Minimum Width of Cavity Opening - Rear

24 1/2*

622*

Minimum Height

21-1/2*

546*

Minimum Depth from Front to Rear

16*

467*

*You will need to add additional clearances to these dimensions for your specific installation. Also allow suf- ficient clearance if you are installing an outside air kit.

NOTE: Refer to chimney liner manufacturer for recom- mendations on supporting the liner. Installation into fireplaces without a permit will void the listing.

NOTICE: In Canada when using a factory-built chimney it must be safety listed, Type UL103 HT (2100oF) [1149oC] CLASS “A” or conforming to CAN/ULC-S629M, STANDARD FOR 650oC FACTORY-BUILT CHIMNEYS.

WARNING

Fire Risk.

When lining air-cooled factory-built chimneys:.

Run chimney liner approved to UL 1777 Type HT requirements (2100 degrees F)

Re-install original factory built chimney cap

ONLY

DO NOT block cooling air openings in chimney

Blocking cooling air will overheat the chimney

To maintain the functionality of the fireplace’s chimney system you may use a Simpson Dura-Vent DuraLiner Slip Hanger, Part # 4671, and attach to the bottom of the fireplace chimney cap to support the liner. You have two options to completing the installation.

Option one - Not required to use liner cap: Re-attach the existing top of the chimney cap.

Option two - Using liner cap:

Re-attach the existing top of the chimney cap and install a new storm collar and a new liner cap.

WARNING! Risk of Fire!

Follow venting manufacturer’s clearances and instructions when installing venting system.

36

Heatilator • ECO-WINS187065-132B • August 29 2011

Image 36
Contents Fire may result causing property ModelIf the information in these instruc Tions is not followed exactly, aHeatilator ECO-WINS18 7065-132B August 29 Mfg Date Table of Contents Heatilator ECO-CHOICE Warranty Warranty Exclusions BTU & Efficiency Specifications Glass SpecificationsListing and Code Approvals Appliance CertificationOperating Instructions Your Wood ApplianceFire Safety OverfiringCombustible/Non-combustible Materials Seasoned WoodBurning Process Second StageKindling or First Stage Final StageBurn Rate Air Control Burn Rates and Operating EfficiencyCorrect Baffle & Blanket Placement Fire RiskBuilding a Fire Wood Fuel & Storage Hardwood vs SoftwoodBlower Control Box & Snap Disc Operating Instructions Blower Operating InstructionsFrequently Asked Questions Clear SpaceOpacity Smoke Quick Start Guide Your specific modelMaintenance and Service Chimney and Chimney Connector Inspection/CleaningDisposal of Ashes Appliance Inspection RoutineGlass Cleaning Inspect Firebrick & Replacement InstructionsFrequency As desired Quick Reference Maintenance Guide MonthlyTroubleshooting Guide Start Fire Problems Possible Cause SolutionService Parts Replacement Glass Replacement Snap Disc Replacement ContdSnap Disc Replacement Wiring DiagramBlower Replacement Shock RiskDoor Handle Assembly Baffle & Ceramic Blanket RemovalTube Channel Assembly Replacement Design and Installation Considerations Getting StartedDraft Negative Pressure Locating Your Appliance & Chimney Chimney Termination RequirementsRule Tools And Supplies Needed Inspect Appliance and ComponentsDimensions and Clearances Appliance DimensionsSurround Sizes SideWall Mantel ClearanceThermal Protection Required Ember Protection OnlyConversion Procedure Alternate Floor Protection CalculationThermal Conductivity k value Thermal Resistance R valueChimney Systems Venting SystemsInspections Larger ChimneysMasonry Chimney Cont’d Metal Heat Circulating Masonry Prefabricated Metal ChimneySecuring Chimney Components Altering the FireplaceFactory-Built Sold Fuel Fireplace Ovalizing Round Stainless Steel Liners Chimney Height / Rise and RunOutside Air Kit Installation Outside Air Installation InstructionsAppliance Set-up Outside Air Kit OptionOptional Offset Adapter Installation Securing Stove Pipe/Liner to Flue CollarStandard Surround & Trim Kit Installation Securing Appliance to Stove Pipe/LinerMobile Home Installation ECO-WINS18 Reference MaterialsService Parts #6 Bay Side/Blower AssemblyStocked At Depot#12 Door Assembly #13 Brick Assembly#24 Burn Rate Control Assembly Fastener PacksService And Maintenance Log Date of Service Performed By Description of ServiceContact Information For Consumer Care

ECO-WINS18 specifications

The Heatiator ECO-WINS18 is a cutting-edge heating solution designed to elevate warmth and comfort in residential and commercial spaces. This innovative unit embodies modern technology, efficiency, and user-centric design, making it a noteworthy choice for anyone in the market for a reliable heating system.

One of the standout features of the ECO-WINS18 is its advanced energy efficiency. This unit boasts a high efficiency rating, significantly reducing energy consumption while delivering powerful heating capabilities. This translates to lower energy bills and a reduced carbon footprint, aligning with growing environmental consciousness among consumers.

The ECO-WINS18 employs a dual heating system that includes both convection and radiant heat technologies. This hybrid approach ensures rapid heat distribution throughout the room, providing consistent warmth while eliminating cold spots. The convection component circulates warm air, while the radiant heat warms objects and surfaces directly, creating a cozy atmosphere.

User convenience is a priority in the design of the ECO-WINS18. It comes equipped with a user-friendly digital thermostat that allows precise temperature control with ease. Additionally, the unit features programmable settings, enabling users to customize heating schedules to suit their lifestyle. This not only enhances comfort but also promotes energy savings.

Safety is a critical consideration in any heating appliance, and the ECO-WINS18 excels in this area as well. It includes multiple safety features such as overheat protection and a tip-over switch that automatically shuts the unit down if it is accidentally knocked over. This ensures peace of mind for users, especially in homes with children and pets.

The sleek and modern design of the ECO-WINS18 allows it to blend seamlessly with various decors, making it an aesthetic addition to any room. The compact size of the unit makes it easy to install, and it can be used as a standalone piece or integrated with existing heating systems.

In summary, the Heatiator ECO-WINS18 stands out for its superior energy efficiency, dual heating technology, user-friendly controls, and safety features. Its modern design not only enhances interior aesthetics but also offers practical functionality. For those seeking an effective and reliable heating solution, the ECO-WINS18 is a wise investment that promises comfort and efficiency for years to come.