E.Baffle & Ceramic Blanket Removal
1.Remove all ash from the firebox, and extinguish all hot embers before disposal into a metal container.
2.Remove the baffle protection channel by rotating it down from the front tube. Figure 23.1.
3.The baffle board has 2 pieces. With the ceramic blanket still in place, slide one baffle piece over the top of other one and pull out top piece through the door opening and then remove bottom baffle piece. Figure 23.2.
4.Remove the ceramic blanket.
5.
6.Slide the baffle pieces one piece at a time underneath the blanket. Be sure the baffle boards are even with the front manifold tube and is resting on all tubes. Figure 22.1 and 22.2.
7.
Baffle Boards & Blanket even with front tube and resting on back tube
Baffle |
| Ceramic Blanket on Top |
|
|
|
|
|
| ||||||||||||||||||
Protection |
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
| ||||||
Channel |
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
| ||||||
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
| |||||||
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
Manifold Tubes 2 pc Baffle Board
Figure 23.1
Figure 23.2
F. Door Handle Assembly
1.Install washer on door handle shaft.
2.Slide door handle through door.
3.Install additional washer(s) as shown in Figure 23.3.
4.Install key in groove.
5.Align groove in latch cam with key; slide latch cam over shaft
6.Install locknut but do not overtighten, the handle needs to move smoothly.
7.Install handle turning in a
CAUTION! Do not overtighten lock nut. The door handle needs to move smoothly.
| Door Cross Section |
Latch Cam | (example) |
Locknut |
|
| Spring |
| Handle |
| Door Handle |
| Spacing |
| Washers |
| Square Key |
Figure 23.3
Heatilator • | 23 |