Heatiator ECO-WINS18 Ovalizing Round Stainless Steel Liners, Chimney Height / Rise and Run

Page 38

J. Ovalizing Round Stainless Steel Liners

Ovalizing round stainless steel liners to accommodate the liner passing through the damper region of a fireplace is an allowable and acceptable practice.

Ensure that the ovalization is minimized to the extent required to fit through the damper.

K. Chimney Height / Rise and Run

To be sure that your Heatilator insert burns properly, the chimney draft (static pressure) should be approximately -0.10 inches water column (W.C.) during a high burn and -0.04 inches W.C. during a low burn, measured 6 inches (152mm) above the top of the insert after one hour of operation at each burn setting.

NOTE: These are guidelines only, and may vary somewhat for individual installations.

This product was designed for and tested on a 6 inch (152mm) chimney, 14 to 16 feet (4.27-4.87m) high, (in- cludes appliance height) measured from the base of the appliance.

The further your stack height or diameter varies from this configuration, the possibility of performance problems ex- ists.

Chimney height may need to be increased by 2 - 3% per each 1000 feet (304.8m) above sea level.

It is not recommended to use offsets or elbows at altitudes above 4000 feet (1219.2m) above sea level or when there are other factors that affect flue draft.

WARNING

Fire Risk.

Do NOT pack insulation or other combustibles between spacers.

ALWAYS maintain specified clearances around venting and spacers.

Install spacers as specified.

Failure to keep insulation or other material away from vent pipe may cause fire.

WARNING

Fire Risk.

This appliance relies upon natural draft to operate properly.

Chimney heights exceeding 25 feet (7.62m) from base of appliance may create an over-draft situation.

Overdraft condition may create over-firing.

Over-firing may ignite creosote and/or damage appli- ance and chimney.

WARNING

Fire Risk.

Failure to install a full reline may cause:

Creosote accumulation creating increased risk of chimney fire.

Lose protection to combustible surfaces from the liner in case of fire.

Poor performance and start-ups.

Less access to chimney for required maintenance.

38

Heatilator • ECO-WINS187065-132B • August 29 2011

Image 38
Contents If the information in these instruc Fire may result causing propertyModel Tions is not followed exactly, aHeatilator ECO-WINS18 7065-132B August 29 Mfg Date Table of Contents Heatilator ECO-CHOICE Warranty Warranty Exclusions Listing and Code Approvals BTU & Efficiency SpecificationsGlass Specifications Appliance CertificationOperating Instructions Your Wood ApplianceCombustible/Non-combustible Materials Fire SafetyOverfiring Seasoned WoodKindling or First Stage Burning ProcessSecond Stage Final StageBurn Rate Air Control Burn Rates and Operating EfficiencyCorrect Baffle & Blanket Placement Fire RiskBuilding a Fire Wood Fuel & Storage Hardwood vs SoftwoodBlower Control Box & Snap Disc Operating Instructions Blower Operating InstructionsOpacity Smoke Frequently Asked QuestionsClear Space Quick Start Guide Your specific modelDisposal of Ashes Maintenance and ServiceChimney and Chimney Connector Inspection/Cleaning Appliance Inspection RoutineFrequency As desired Glass CleaningInspect Firebrick & Replacement Instructions Quick Reference Maintenance Guide MonthlyTroubleshooting Guide Start Fire Problems Possible Cause SolutionSnap Disc Replacement Service Parts ReplacementGlass Replacement Snap Disc Replacement Contd Wiring DiagramBlower Replacement Shock RiskDoor Handle Assembly Baffle & Ceramic Blanket RemovalTube Channel Assembly Replacement Draft Design and Installation ConsiderationsGetting Started Negative Pressure Locating Your Appliance & Chimney Chimney Termination RequirementsRule Tools And Supplies Needed Inspect Appliance and ComponentsSurround Sizes Dimensions and ClearancesAppliance Dimensions SideWall Mantel ClearanceThermal Protection Required Ember Protection OnlyThermal Conductivity k value Conversion ProcedureAlternate Floor Protection Calculation Thermal Resistance R valueInspections Chimney SystemsVenting Systems Larger ChimneysMasonry Chimney Cont’d Metal Heat Circulating Masonry Prefabricated Metal ChimneyFactory-Built Sold Fuel Fireplace Securing Chimney ComponentsAltering the Fireplace Ovalizing Round Stainless Steel Liners Chimney Height / Rise and RunAppliance Set-up Outside Air Kit InstallationOutside Air Installation Instructions Outside Air Kit OptionOptional Offset Adapter Installation Securing Stove Pipe/Liner to Flue CollarStandard Surround & Trim Kit Installation Securing Appliance to Stove Pipe/LinerMobile Home Installation ECO-WINS18 Reference MaterialsStocked Service Parts#6 Bay Side/Blower Assembly At Depot#12 Door Assembly #13 Brick Assembly#24 Burn Rate Control Assembly Fastener PacksService And Maintenance Log Date of Service Performed By Description of ServiceContact Information For Consumer Care

ECO-WINS18 specifications

The Heatiator ECO-WINS18 is a cutting-edge heating solution designed to elevate warmth and comfort in residential and commercial spaces. This innovative unit embodies modern technology, efficiency, and user-centric design, making it a noteworthy choice for anyone in the market for a reliable heating system.

One of the standout features of the ECO-WINS18 is its advanced energy efficiency. This unit boasts a high efficiency rating, significantly reducing energy consumption while delivering powerful heating capabilities. This translates to lower energy bills and a reduced carbon footprint, aligning with growing environmental consciousness among consumers.

The ECO-WINS18 employs a dual heating system that includes both convection and radiant heat technologies. This hybrid approach ensures rapid heat distribution throughout the room, providing consistent warmth while eliminating cold spots. The convection component circulates warm air, while the radiant heat warms objects and surfaces directly, creating a cozy atmosphere.

User convenience is a priority in the design of the ECO-WINS18. It comes equipped with a user-friendly digital thermostat that allows precise temperature control with ease. Additionally, the unit features programmable settings, enabling users to customize heating schedules to suit their lifestyle. This not only enhances comfort but also promotes energy savings.

Safety is a critical consideration in any heating appliance, and the ECO-WINS18 excels in this area as well. It includes multiple safety features such as overheat protection and a tip-over switch that automatically shuts the unit down if it is accidentally knocked over. This ensures peace of mind for users, especially in homes with children and pets.

The sleek and modern design of the ECO-WINS18 allows it to blend seamlessly with various decors, making it an aesthetic addition to any room. The compact size of the unit makes it easy to install, and it can be used as a standalone piece or integrated with existing heating systems.

In summary, the Heatiator ECO-WINS18 stands out for its superior energy efficiency, dual heating technology, user-friendly controls, and safety features. Its modern design not only enhances interior aesthetics but also offers practical functionality. For those seeking an effective and reliable heating solution, the ECO-WINS18 is a wise investment that promises comfort and efficiency for years to come.