Heatiator ADI60S Appliance Setup, Remove Shipping Materials, Clean the Appliance, Accessories

Page 20

11 Appliance Setup

A. Remove Shipping Materials

Remove shipping materials from inside or underneath the ﬁrebox.

Placing the Ember Material

Ember material is shipped with this gas appliance. To place the ember material:

• Embers CANNOT be placed directly over ports.

B. Clean the Appliance

Clean/vacuum any sawdust that may have accumulated inside the ﬁrebox or underneath in the control cavity.

C. Accessories

Install approved accessories per instructions included with accessories. See Service Parts List for appropriate accessories. Refer to Section 15.

WARNING

Shock or ﬁre risk.

Use ONLY optional accessories approved for this appliance.

•Using non-listed accessories voids warranty.

•Using non-listed accessories may result in a safety hazard.

•Only Hearth & Home Technologies approved

accessories may be used safely.

•When placing Glowing Embers® onto the burner care should be taken so that the ports are not covered. Place the dime-size ember pieces near port holes in burner top, sides and front (see Figure 11.1). Failure to follow this procedure will likely cause lighting and sooting problems.

EMBER MATERIAL/BRAISES

Figure 11.1 Placement of Embers

D. Ember Placement

WARNING

Explosion Risk.

•Follow ember placement instructions in manual.

•Do NOT place embers directly over burner ports.

•Replace ember material annually.

Improperly placed embers interferes with proper burner operation.

•Place Mystic Ember over burner surface and around base of burner. Do not cover any burner port holes. Use this material to give the appliance a realistic ash bed.

•Save the remaining ember materials for use during appliance servicing. The embers provided should be enough for 3 to 5 applications.

20	Heatilator • ADI60S • 345-900 Rev. G • 9/08

Image 20

Contents HOT Surfaces ModelWhat to do if you smell gas Homeowner Reference Information XxxxxxxxTable of Contents Listing and Code Approvals Design and Installation Considerations Getting StartedTools and Supplies Needed Inspect Appliance and ComponentsADI60 Fireplace Size RequirementsMinimum Fireplace Opening Clearances Clearances to Mantels or other Combustibles above ApplianceTermination Locations Vent Termination Minimum ClearancesVent Information and Diagrams Vent Table KeyHorizontal Venting Measuring StandardsInstallation Preparation Venting Components Installing Vent Pipe and ApplianceConnecting Vent Pipe Placing, Securing and Leveling the Appliance Installing Adaptor and Termination Cap Factory Built Wood BurningDamper Flashing Kit Optional Class a PipeGas Pressures Gas InformationFuel Conversions Gas Connection High Altitude Installations Check for GAS LeaksWiring the Appliance ON/OFF SwitchElectrical Information Appliance RequirementsJunction Box Installation Optional AccessoriesFAN Junction BOX Finishing Mantel ProjectionsAppliance Setup Clean the ApplianceAccessories Ember PlacementRefractory Placement Models Supreme-XT, Grand-XTQVI30, QVI35, ADI60 Refractory from the packagingLog Set Assembly LOGS-ADI60 Positioning the LogsAreas for LOG #4 Placement Heatilator ADI60S 345-900 Rev. G 9/08 Glass Assembly Air Shutter SettingRemoving Glass Assembly Replacing Glass AssemblyBefore operating this appliance have a qualified technician Operating InstructionsBefore Lighting Appliance What to do if YOU Smell GAS Lighting ApplianceStanding Pilot Ignition After Appliance is Lit Initial Break-in ProcedureCheck Pilot Flame Appearance Frequently Asked Questions Issue SolutionsStanding Pilot Ignition System TroubleshootingSymptom Possible Causes Corrective Action Troubleshooting Symptom Possible Cause Corrective ActionMaintenance Tasks Maintaining and Servicing ApplianceInspect Maintenance Tasks Doors, SurroundsAppliance Dimension Diagram Reference MaterialsVent Kits Components Direct Vent Flex Liner KitsPart number list on following Log Set AssemblyService Parts Service Parts At DepotStanding Pilot Valve Assembly StockedCONDITIONS, Exclusions & Limitation of Liability Limited Lifetime Warranty Contact Information