Heatiator ADI60S owner manual Vent Information and Diagrams, Vent Table Key, Horizontal Venting

Page 9

5 Vent Information and Diagrams

A. Vent Table Key

The abbreviations listed in this vent table key are used in the vent diagrams.

Symbol	Description
VMIN	Minimum Vertical Run Length 14 ft.
VMIN	Maximum Vertical Run Length 50 ft.

B. Horizontal Venting

Horizontal venting is NOT allowed.

C. Measuring Standards

Vertical measurements listed in the vent diagram (Figure

5.1) were made using the following standard:

• Vertical terminations are measured to top of chimney.

WARNING

Fire Hazard. Explosion Risk. Asphyxiation Risk.

Do NOT connect this gas appliance to a chimney ﬂue serving a separate solid fuel or gas burning appliance.

•May impair safe operation of this appliance or other appliances connected to the ﬂue.

•Vent this appliance directly outside.

•Use separate vent system for this appliance.

CAUTION

ALL vent speciﬁcations MUST be followed.

•This product is tested and listed to these speciﬁcations.

•Appliance performance will suffer if speciﬁcations are not followed.

TERMINATION CAP

ADAPTOR

EXHAUST VENT PIPE

INSULATION SEAL

INLET VENT AIR PIPE

Figure 5.1

Heatilator • ADI60S • 345-900 Rev. G • 9/08

9

Image 9

Contents Model What to do if you smell gasHOT Surfaces Xxxxxxxx Homeowner Reference InformationTable of Contents Listing and Code Approvals Getting Started Design and Installation ConsiderationsTools and Supplies Needed Inspect Appliance and ComponentsFireplace Size Requirements Minimum Fireplace OpeningADI60 Clearances to Mantels or other Combustibles above Appliance ClearancesVent Termination Minimum Clearances Termination LocationsVent Table Key Vent Information and DiagramsHorizontal Venting Measuring StandardsInstallation Preparation Installing Vent Pipe and Appliance Connecting Vent PipeVenting Components Placing, Securing and Leveling the Appliance Factory Built Wood Burning Installing Adaptor and Termination CapDamper Flashing Kit Optional Class a PipeGas Information Fuel Conversions Gas ConnectionGas Pressures Check for GAS Leaks High Altitude InstallationsON/OFF Switch Wiring the ApplianceElectrical Information Appliance RequirementsOptional Accessories Junction Box InstallationFAN Junction BOX Mantel Projections FinishingClean the Appliance Appliance SetupAccessories Ember PlacementModels Supreme-XT, Grand-XT Refractory PlacementQVI30, QVI35, ADI60 Refractory from the packagingPositioning the Logs Log Set Assembly LOGS-ADI60Areas for LOG #4 Placement Heatilator ADI60S 345-900 Rev. G 9/08 Air Shutter Setting Glass AssemblyRemoving Glass Assembly Replacing Glass AssemblyOperating Instructions Before Lighting ApplianceBefore operating this appliance have a qualified technician Lighting Appliance Standing Pilot IgnitionWhat to do if YOU Smell GAS Initial Break-in Procedure Check Pilot Flame AppearanceAfter Appliance is Lit Issue Solutions Frequently Asked QuestionsTroubleshooting Symptom Possible Causes Corrective ActionStanding Pilot Ignition System Symptom Possible Cause Corrective Action TroubleshootingMaintaining and Servicing Appliance Maintenance TasksDoors, Surrounds Inspect Maintenance TasksReference Materials Appliance Dimension DiagramDirect Vent Flex Liner Kits Vent Kits ComponentsLog Set Assembly Service PartsPart number list on following At Depot Service PartsStocked Standing Pilot Valve AssemblyCONDITIONS, Exclusions & Limitation of Liability Limited Lifetime Warranty Contact Information