Heatiator ADI60S owner manual Vent Kits Components, Direct Vent Flex Liner Kits

Page 35

B. Vent Kits Components

Direct Vent Flex Liner Kits (see Figure 15.2)

LINK-DV-30B or (LINK-DV-30): Masonry 3 inch ﬂex liner

kit. Expands to 30 feet. Includes: two liners, termination cap, ﬂashing, and link adapter.

LINK-DV4-30B or (LINK-DV4-30): Masonry 3 inch ﬂex liner kit. Expands to 30 feet and 4 feet respectively. Includes: two liners, termination cap, ﬂashing, and link adapter.

LINK-DV30B	LINK-DV4-30B
Installation	Installation

TERMINATION

CAP

EXHAUST

AIR

VENT PIPE

WARNING:

DO NOT BLOCK

THIS PIPE END!

INLET AIR

VENT PIPE

OPTIONAL LINK-ZC-ADPB

FOR USE WITH CLASS A

WOODBURNING PIPE

Figure 15.2 Direct Vent Flex Liner Kits

Direct Vent Flex Liner Accessory Kits (see Figure 15.3)

Flash-Damp: Zero clearance damper ﬂashing kit for use with LINK-DV-30B or LINK-DV4-30B liner kits.

LINK-ZC-ADP: Zero clearance chimney adapter

SVRLINK-ADP: Adapter kit (colinear to coaxial 3 inches included in above kits).

FLEX3-30: One 3 inch ﬂexible liner expands to 30 feet.

FLEX3-30/2: Two 3 inch ﬂexible liners expands to 30 feet each.

FLEX-CNCT: Connector kit - 3 inch liner to 3 inch liner, one connector per kit.

FLASH-DAMP

LINK-ZC-ADP

SVRLINK-ADP

FLEX3-30

FLEX3-30/2

FLEX3-CNCT

Figure 15.3 Direct Vent Flex Liner Accessory Kits

Heatilator • ADI60S • 345-900 Rev. G • 9/08

35

Image 35

Contents HOT Surfaces ModelWhat to do if you smell gas Xxxxxxxx Homeowner Reference InformationTable of Contents Listing and Code Approvals Inspect Appliance and Components Design and Installation ConsiderationsGetting Started Tools and Supplies NeededADI60 Fireplace Size RequirementsMinimum Fireplace Opening Clearances to Mantels or other Combustibles above Appliance ClearancesVent Termination Minimum Clearances Termination LocationsMeasuring Standards Vent Information and DiagramsVent Table Key Horizontal VentingInstallation Preparation Venting Components Installing Vent Pipe and ApplianceConnecting Vent Pipe Placing, Securing and Leveling the Appliance Class a Pipe Installing Adaptor and Termination CapFactory Built Wood Burning Damper Flashing Kit OptionalGas Pressures Gas InformationFuel Conversions Gas Connection Check for GAS Leaks High Altitude InstallationsAppliance Requirements Wiring the ApplianceON/OFF Switch Electrical InformationOptional Accessories Junction Box InstallationFAN Junction BOX Mantel Projections FinishingEmber Placement Appliance SetupClean the Appliance AccessoriesRefractory from the packaging Refractory PlacementModels Supreme-XT, Grand-XT QVI30, QVI35, ADI60Positioning the Logs Log Set Assembly LOGS-ADI60Areas for LOG #4 Placement Heatilator ADI60S 345-900 Rev. G 9/08 Replacing Glass Assembly Glass AssemblyAir Shutter Setting Removing Glass AssemblyBefore operating this appliance have a qualified technician Operating InstructionsBefore Lighting Appliance What to do if YOU Smell GAS Lighting ApplianceStanding Pilot Ignition After Appliance is Lit Initial Break-in ProcedureCheck Pilot Flame Appearance Issue Solutions Frequently Asked QuestionsStanding Pilot Ignition System TroubleshootingSymptom Possible Causes Corrective Action Symptom Possible Cause Corrective Action TroubleshootingMaintaining and Servicing Appliance Maintenance TasksDoors, Surrounds Inspect Maintenance TasksReference Materials Appliance Dimension DiagramDirect Vent Flex Liner Kits Vent Kits ComponentsPart number list on following Log Set AssemblyService Parts At Depot Service PartsStocked Standing Pilot Valve AssemblyCONDITIONS, Exclusions & Limitation of Liability Limited Lifetime Warranty Contact Information