Heatiator ADI60S owner manual Stocked, Standing Pilot Valve Assembly

Page 38

Service Parts	ADI60S

Service Parts Diagram	Beginning Manufacturing Date: July 2007
	Ending Manufacturing Date: ______

Standing Pilot Valve Assembly	1
	1
	2
	3
	14
4	13
5
6
7
8
9	12
10
11

IMPORTANT: THIS IS DATED INFORMATION. When requesting service or replacement				Stocked
parts for your appliance please provide model number and serial number. All parts listed				Stocked
in this manual may be ordered from an authorized dealer.				at Depot
ITEM	DESCRIPTION	COMMENTS	PART NUMBER
1	Pilot Assembly NG		2103-010	Y
1	Pilot Assembly LP		2103-011	Y
	Pilot Assembly LP		2103-011	Y
2	Pilot Bracket		319-164
3	Shutter Bracket Assembly		2026-130	Y
4	Valve Plate Gasket		319-401
5	Top Handle		319-170
6	Bottom Handle		319-168
7	Bracket		319-120
8	Valve Bracket		319-146
9	Flexible Gas Connector		477-301A	Y
10	Valve NG		230-0710	Y
10	Valve LP		230-0720	Y
	Valve LP		230-0720	Y
11	Flex Ball Valve Assembly		531-320A	Y
12	Temp Sensor Switch		046-530	Y
13	Bracket: Burner Support		319-166
14	Burner Neck		319-336	Y
	Wire Assembly		2020-069	Y
	Oriﬁce NG (#35C)		582-835	Y
	Oriﬁce LP (#52C)		582-852	Y

38	Heatilator • ADI60S • 345-900 Rev. G • 9/08

Image 38

Contents HOT Surfaces ModelWhat to do if you smell gas Homeowner Reference Information XxxxxxxxTable of Contents Listing and Code Approvals Tools and Supplies Needed Design and Installation ConsiderationsGetting Started Inspect Appliance and ComponentsADI60 Fireplace Size RequirementsMinimum Fireplace Opening Clearances Clearances to Mantels or other Combustibles above ApplianceTermination Locations Vent Termination Minimum ClearancesHorizontal Venting Vent Information and DiagramsVent Table Key Measuring StandardsInstallation Preparation Venting Components Installing Vent Pipe and ApplianceConnecting Vent Pipe Placing, Securing and Leveling the Appliance Damper Flashing Kit Optional Installing Adaptor and Termination CapFactory Built Wood Burning Class a PipeGas Pressures Gas InformationFuel Conversions Gas Connection High Altitude Installations Check for GAS LeaksElectrical Information Wiring the ApplianceON/OFF Switch Appliance RequirementsJunction Box Installation Optional AccessoriesFAN Junction BOX Finishing Mantel ProjectionsAccessories Appliance SetupClean the Appliance Ember PlacementQVI30, QVI35, ADI60 Refractory PlacementModels Supreme-XT, Grand-XT Refractory from the packagingLog Set Assembly LOGS-ADI60 Positioning the LogsAreas for LOG #4 Placement Heatilator ADI60S 345-900 Rev. G 9/08 Removing Glass Assembly Glass AssemblyAir Shutter Setting Replacing Glass AssemblyBefore operating this appliance have a qualified technician Operating InstructionsBefore Lighting Appliance What to do if YOU Smell GAS Lighting ApplianceStanding Pilot Ignition After Appliance is Lit Initial Break-in ProcedureCheck Pilot Flame Appearance Frequently Asked Questions Issue SolutionsStanding Pilot Ignition System TroubleshootingSymptom Possible Causes Corrective Action Troubleshooting Symptom Possible Cause Corrective ActionMaintenance Tasks Maintaining and Servicing ApplianceInspect Maintenance Tasks Doors, SurroundsAppliance Dimension Diagram Reference MaterialsVent Kits Components Direct Vent Flex Liner KitsPart number list on following Log Set AssemblyService Parts Service Parts At DepotStanding Pilot Valve Assembly StockedCONDITIONS, Exclusions & Limitation of Liability Limited Lifetime Warranty Contact Information