Heatiator ADI60S Installing Vent Pipe and Appliance, Venting Components, Connecting Vent Pipe

Page 11

7 Installing Vent Pipe and Appliance

A. Venting Components

CAUTION

Sharp Edges

•Wear protective gloves and safety glasses during installation.

The vertical vent termination system installed on this model includes:

•One length of 3-inch ﬂexible vent pipe for combustion air (included with vent kit). Pipe will be either a 4-foot or 30-foot section depending on which kit is being used in the application.

•Flexible vent pipe for exhaust air (included with vent kit).

•One pipe-to-cap adaptor (included with vent kit).

•One vertical termination cap (included with vent kit).

B. Connecting Vent Pipe

Reference instructions in the termination kit.

•Install the 3-inch ﬂexible vent pipe(s) down through the chimney.

•Use three screws to secure the exhaust ﬂexible vent pipe to the 3 foot section stainless steel ﬂexible vent pipe using the factory-installed 3-inch collar in the stainless steel section of pipe (see Figure 7.1).

•Use 3 screws to attach either a 4 foot or 30 foot section of inlet air vent to the inlet collar on the collar slide plate (see Figure 7.1). NOTE: The collar slide plate may be removed from appliance to aid installation.

•Seal opening between ﬂex vent and chimney just above insert. Non-combustible, unfaced ﬁberglass insulation may be used for this purpose.

TERMINATION
CAP
			INLET AIR STARTING COLLAR
EXHAUST
AIR			LOCKING TAB
VENT PIPE			LOCKING TAB
VENT PIPE
			STARTING COLLAR BRACKET
		EXHAUST STARTING COLLAR
INLET AIR
VENT PIPE
INLET AIR STARTING COLLAR
STARTING COLLAR BRACKET
EXHAUST STARTING COLLAR
Figure 7.1
Heatilator • ADI60S	• 345-900 Rev. G	•	9/08	11

Image 11

Contents HOT Surfaces ModelWhat to do if you smell gas Xxxxxxxx Homeowner Reference InformationTable of Contents Listing and Code Approvals Inspect Appliance and Components Design and Installation ConsiderationsGetting Started Tools and Supplies NeededADI60 Fireplace Size RequirementsMinimum Fireplace Opening Clearances to Mantels or other Combustibles above Appliance ClearancesVent Termination Minimum Clearances Termination LocationsMeasuring Standards Vent Information and DiagramsVent Table Key Horizontal VentingInstallation Preparation Venting Components Installing Vent Pipe and ApplianceConnecting Vent Pipe Placing, Securing and Leveling the Appliance Class a Pipe Installing Adaptor and Termination CapFactory Built Wood Burning Damper Flashing Kit OptionalGas Pressures Gas InformationFuel Conversions Gas Connection Check for GAS Leaks High Altitude InstallationsAppliance Requirements Wiring the ApplianceON/OFF Switch Electrical InformationOptional Accessories Junction Box InstallationFAN Junction BOX Mantel Projections FinishingEmber Placement Appliance SetupClean the Appliance AccessoriesRefractory from the packaging Refractory PlacementModels Supreme-XT, Grand-XT QVI30, QVI35, ADI60Positioning the Logs Log Set Assembly LOGS-ADI60Areas for LOG #4 Placement Heatilator ADI60S 345-900 Rev. G 9/08 Replacing Glass Assembly Glass AssemblyAir Shutter Setting Removing Glass AssemblyBefore operating this appliance have a qualified technician Operating InstructionsBefore Lighting Appliance What to do if YOU Smell GAS Lighting ApplianceStanding Pilot Ignition After Appliance is Lit Initial Break-in ProcedureCheck Pilot Flame Appearance Issue Solutions Frequently Asked QuestionsStanding Pilot Ignition System TroubleshootingSymptom Possible Causes Corrective Action Symptom Possible Cause Corrective Action TroubleshootingMaintaining and Servicing Appliance Maintenance TasksDoors, Surrounds Inspect Maintenance TasksReference Materials Appliance Dimension DiagramDirect Vent Flex Liner Kits Vent Kits ComponentsPart number list on following Log Set AssemblyService Parts At Depot Service PartsStocked Standing Pilot Valve AssemblyCONDITIONS, Exclusions & Limitation of Liability Limited Lifetime Warranty Contact Information