Desa VN18T, VP26, VN30T, VP16, VP22IT Mounting Heater to Floor, Installing Bottom Mounting Screws

Page 10

10

INSTALLATION

Installing Heater To Wall (Cont.) Mounting Heater To Floor

INSTALLATION

Continued

Installing Bottom Mounting Screws

1.Locate two bottom mounting holes. These holes are near bot- tom on back panel of heater (see Figure 12).

2.Mark screw locations on wall.

3.Remove heater from mounting bracket.

4.If installing bottom mounting screws into hollow or solid wall, install wall anchors. Follow steps 1 through 4 under Attaching To Wall Anchor Method, page 9.

If installing bottom mounting screw into wall stud, drill holes at marked locations using 9/64" drill bit.

5.Replace heater onto mounting bracket.

6.Place spacers between bottom mounting holes and wall anchor or drilled hole.

7.Hold spacer in place with one hand. With other hand, insert mounting screw through bottom mounting hole and spacer. Place tip of screw in opening of wall anchor or drilled hole.

8.Tighten both screws until heater is firmly secured to wall. Do not over tighten.

Note: Do not replace front panel at this time. Replace front panel after making gas connections and checking for leaks (see pages 11 and 12).

MOUNTING HEATER TO FLOOR

Mounting Base Feet to Heater

1.Lay heater cabinet on its back on a table with the heater bot- tom overhanging the table edge.

2.Align holes in base foot with mounting holes on bottom of cabinet (see Figure 13).

3.Secure base foot to heater using sheet metal screws.

4.Repeat for other side.

Mounting Base Feet to Floor (Where required by local code)

1.Remove front cover (see Removing Front Panel of Heater, page 8).

2.Position heater with base feet in desired location. Mark holes for drilling. Remove heater with base.

3.For carpeted floors, make a small cut with a sharp knife at marked locations prior to drilling. If mounting base to a wood floor, drill 1/8 inch diameter hole, 3/4 inch deep. (Do not use anchors in wood floors).

If mounting base to a concrete floor, drill with 1/4 inch diam- eter concrete drill bit, 13/8 inches into floor. Insert anchors com- pletely into holes.

4.Reposition heater with base feet over holes. Secure base to floor with wood screws. See Figure 13.

Wood

Screw

Front View

Wall

Heater

Base Foot

Spacer

Sheet Metal Screw

Side View

Figure 13 - Installing Base Feet

Figure 12 - Installing Bottom Mounting Screws

For..com

107887-01E

Page 9 Page 11
Image 10
Page 9 Page 11
Contents VP16IT, VN18IT VP22IT, VN25IT Safety Information and Installation ManualWhat to do if YOU Smell GAS Table of Contents Safety InformationUnpacking Safety Information Product IdentificationProduct Features Local CodesUnusually Tight Construction AIR for Combustion and VentilationProviding Adequate Ventilation Confined and Unconfined SpaceDetermining FRESH-AIR Flow for Heater Location Determining if You Have a Confined or Unconfined SpaceVentilation Air From Inside Building Ventilation AIRVentilation Air From Outdoors Check GAS Type InstallationInstallation Items Locating HeaterInstalling Heater to Wall Thermostat Sensing BulbAttaching Mounting Bracket To Wall Placing Heater On Mounting BracketMounting Heater to Floor Installing Bottom Mounting ScrewsMounting Base Feet to Floor Where required by local code Mounting Base Feet to HeaterConnecting to GAS Supply Typical Inlet Pipe DiametersPressure Testing Heater Gas Connections Pressure Testing Gas Supply Piping SystemChecking GAS Connections Operating Heater NON-THERMOSTAT Models For Your Safety Read Before LightingLighting Instructions To Select Heating Level Manual Lighting ProcedureThermostat Models For Your Safety Read Before Lighting To Turn OFF GAS to ApplianceVP16T VP26T VN18T VN30T Thermostat Operation Burner Patterns, Models VP16IT, VN18IT, VP26IT, & VN30ITCleaning and Maintenance Inspecting HeaterSpecifications VN25ITTroubleshooting Observed Problem Possible Cause RemedyAfter ODS/pilot lights, keep control Observed Problem Possible Cause Illustrated Parts Breakdown Cabinet BodyParts List VN30T Description QTYCabinet Body VP16IT, VN18IT, VP22IT, VN25IT KEY Part Number VP16IT VN18IT VP22IT VN25IT Description QTY Burner Assembly VP16, VN18, VP16T, VN18T, VP16IT, VN18ITVP16T VN18T VP16IT VN18IT Description QTY VP26, VN30, VP26T, VN30T, VP22IT, VN25IT VP26T VN30T VP22IT VN25IT Description QTY Technical Service Replacement PartsService Hints Service Publications AccessoriesOwners Registration Form Postage Required 107887-01E Warranty Information

VN18, VP16, VN18T, VN25IT, VP22IT specifications

Desa VN18, VN30T, VP16, VP26T, and VP16T are a series of innovative devices tailored to meet diverse needs in various applications, ranging from industrial to consumer markets. Each model embodies distinct features, technologies, and characteristics that enhance performance and usability.

The Desa VN18 is renowned for its compact structure and lightweight design, making it ideal for small-scale applications. It integrates a sophisticated energy-efficient system that minimizes power consumption while maximizing output. This model supports various connectivity options, ensuring seamless integration with existing systems. Additionally, the VN18 is equipped with an intuitive user interface that simplifies operation, making it accessible even for those with limited technical experience.

In contrast, the VN30T offers enhanced capabilities suitable for medium to large-scale operations. This model boasts an impressive processing power, enabling it to handle more complex tasks with ease. The VN30T features advanced cooling technologies that keep the unit operating optimally, even under heavy workloads. Furthermore, its durable construction ensures longevity and reliability, making it a preferred choice for industrial environments.

The VP16, designed with versatility in mind, excels in adaptability across multiple applications. It offers interchangeable components, allowing users to customize setup based on specific needs. The technology embedded within the VP16 includes smart sensors that provide real-time feedback, helping users to monitor performance and adjust settings accordingly. This level of adaptability makes the VP16 an invaluable asset in dynamic working conditions.

Next in the lineup is the VP26T, which stands out for its robust performance under demanding conditions. With a focus on safety features, this model includes multiple fail-safes and redundancy systems that ensure consistent operation, even in emergencies. The VP26T is designed for heavy-duty applications, featuring enhanced materials that resist wear and tear, thereby prolonging its lifespan.

Finally, the VP16T combines the best aspects of its predecessors while introducing new technological advancements. It utilizes cutting-edge automation technologies that enable remote control and monitoring, enhancing user convenience. The VP16T's power management system optimizes energy use based on operational demands, contributing to both cost savings and sustainability.

Overall, Desa VN18, VN30T, VP16, VP26T, and VP16T represent a forward-thinking approach to design and functionality, addressing the evolving needs of users across various sectors. With their unique features and robust technologies, these models are set to redefine standards in their respective categories.
Top Page Image Contents