Desa VGL24PRA, VGL24NRA, VGL18PRA Installing Heater Base Assembly, Installation Items Needed

Page 13

INSTALLATION

Continued

INSTALLING HEATER BASE ASSEMBLY

CAUTION: Do not remove the data plates attached to the heater base assembly. The data plates contain important warranty and safety information.

WARNING: You must secure this heater to fireplace floor. If not, heater will move when you adjust controls. Moving heater may cause a gas leak.

WARNING: If installing in a sunken fireplace, special care is needed. You must raise the fireplace floor to allow access to heater control panel. This will insure adequate air flow and guard against sooting and controls being damaged. Raise fireplace floor with noncombus- tible material. Make sure material is secure.

CAUTION: Do not pick up heater base assembly by the burner. This could damage heater. Only handle base as- sembly by grates.

IMPORTANT: Make sure the heater burners are level. If heater is not level, heater will not work properly.

Installation Items Needed

•hardware package (provided with heater)

•approved flexible gas hose (not provided) (if allowed by local codes)

•sealant resistant to propane/LP gas, not pro- vided

•electric drill with 3/16" masonry drill bit

Note: Install optional remote receiver and hand- held remote kit (see Accessories, page 29) before installing gas log heater. See installation instruc- tions included with the kit.

1.Apply pipe joint sealant lightly to male threads of the fitting to be threaded into gas regulator. Connect approved flexible gas hose to gas regulator of heater (see Figure 11).

2.Locate masonry screws in hardware package.

3.Position heater base assembly in fireplace.

4.Place logs in their proper positions on heater base.

5.Center heater base and logs front-to-back and side-to-side in fireplace.

6.Carefully remove logs without moving heater base.

7.Mark screw locations through holes in mount- ing flanges (see Figure 12). If installing in a brick-bottom fireplace, mark screw locations in mortar joint of bricks.

8.Remove heater base from fireplace.

9.Drill holes at marked locations using 3/16" masonry drill bit.

10.Attach base assembly to fireplace floor using two masonry screws (in hardware package) (see Figure 12).

11.Connect to gas supply. See Connecting To Gas Supply, page 14.

Flexible Gas Hose

(if allowed by local codes)

Fitting

Figure 11 - Attaching Flexible Gas Hose

to Heater

Masonry

Screw

Mounting

Flanges

Figure 12 - Attaching Base Assembly to Fireplace Floor

112882-01B

www.desatech.com

13

Page 12 Page 14
Image 13
Page 12 Page 14
Contents What to do if YOU Smell GAS Table of Contents Safety Information Safety Information Remote Control Accessories Product FeaturesProduct Identification Local CodesProviding Adequate Ventilation AIR for Combustion VentilationDetermining FRESH-AIR Flow for Fireplace Location Unusually Tight ConstructionVentilation AIR AIR for Combustion VentilatioinVentilation Air From Inside Building Ventilation Air From Outdoors InstallationLog Size Side Wall Ceiling Check GAS TypeMinimum Firebox Size LogMantel Clearances Determining Minimum Mantel Clearances When Using a HoodMinimum Noncombustible Material Clearances Minimum Mantel Clearances Without Using Hood Floor Clearances Installing Damper Clamp Accessory for Vented OperationInstallation Items Needed Installing Heater Base AssemblyExternal Regulator With Vent Pointing Down Connecting to GAS SupplyTest Pressures In Excess Of 1/2 Psig 3.5 kPa Checking GAS ConnectionsTest Pressures Equal To or Less Than 1/2 Psig 3.5 kPa Equipment Shutoff Valve Installing Optional Remote AccessoriesConnecting Wires Log #1 Installing LogsOperating Heater For Your Safety Read Before LightingLighting Instructions To Turn OFF GAS To Appliance Manual Lighting ProcedureThermostat Series Model Optional HAND-HELD Remote OperationGhrctb ON/OFF Series Model GhrcbInspecting Burners Auto Shutoff FeaturePilot Flame Pattern Main BurnerBurner Injector Holder and Pilot AIR Inlet Hole Cleaning MaintenanceLogs Observed Problem Possible Cause Remedy TroubleshootingSee Cleaning and Mainte Moisture/condensation noticed Statement above Gas leak. See WarningReplacement Parts Wiring DiagramService Hints Technical ServiceReceiver and HAND-HELD Remote Control KIT Ghrcb Series Cleaning KIT CCKInformation Video Equipment Shutoff Valve GA5010Illustrated Parts Breakdown Parts List Keep this Warranty Warranty InformationLimited Warranty VENT-FREE GAS LOG Heaters

VGL18PRA, VGL24NRA, VGL30NRA, VGL24PRA specifications

Desa VGL24NRA, VGL18PRA, VGL30NRA, and VGL24PRA are remarkable models of vented gas logs that have set a benchmark in the market for their outstanding performance and aesthetic appeal. Each of these models has been designed with a unique blend of technology and craftsmanship to cater to diverse consumer preferences while ensuring warmth and comfort.

The Desa VGL24NRA is a 24-inch model equipped with a powerful burner system that delivers impressive heat output while ensuring efficient fuel consumption. Its realistic log set, complete with hand-painted finishes, replicates the look of a traditional wood-burning fireplace, enhancing the visual charm of any living space. Adjustable flame height is another feature that grants users control over the ambiance and heat level.

Moving on to the VGL18PRA, this 18-inch vented gas log set is ideal for smaller fireplaces while delivering substantial warmth. The unit features a piezo ignition system for quick and hassle-free startup. Its compact size does not compromise on aesthetic appeal, as it includes beautifully crafted ceramic logs and ember bed, providing a cozy and inviting atmosphere. The VGL18PRA also boasts a safety pilot system to ensure reliable operation and peace of mind.

For larger spaces, the VGL30NRA provides a robust 30-inch log set, designed for extensive heat output. The heavy-duty burner's longevity and efficiency ensure that homeowners can rely on this model throughout the colder months. Like its smaller counterparts, this model features a realistic log design, but its size allows it to produce an even more prominent flame effect, serving as a focal point in any room.

Lastly, the VGL24PRA model offers an excellent balance of size and efficiency. This 24-inch log set enhances both heating and visual comfort, making it an excellent choice for mid-sized living areas. The model is designed with a rugged, yet elegant finish that complements a variety of home decors. Its advanced safety features and easy-to-use controls further enhance its appeal, making it a functional and stylish addition to any fireplace setup.

Overall, all four models—Desa VGL24NRA, VGL18PRA, VGL30NRA, and VGL24PRA—uphold the brand's dedication to quality, comfort, and innovation. Equipped with advanced technologies, these vented gas logs promise not only to keep homes warm but also to elevate the aesthetic value of any space they inhabit. Whether for small or large fireplaces, these models provide versatility and efficiency, making them a worthwhile investment for homeowners looking to enhance their living experience.
Top Page Image Contents