18
TROUBLESHOOTING
TROUBLESHOOTING
Continued
OBSERVED PROBLEM | POSSIBLE CAUSE | REMEDY | ||
Burner does not light after ODS/pilot is lit | 1. | Burner orifice is clogged | 1. | Clean burner orifice (see Cleaning and |
|
|
|
| Maintenance, page 16) or replace burner |
|
|
|
| orifice |
| 2. | Inlet gas pressure is too low | 2. | Contact local natural or propane/LP gas |
|
|
|
| company |
|
|
|
|
|
Delayed ignition of burner | 1. | Manifold pressure is too low | 1. | Contact local natural or propane/LP gas |
|
|
|
| company |
| 2. | Burner orifice is clogged | 2. | Clean burner orifice (see Cleaning and |
|
|
|
| Maintenance, page 16) or replace burner |
|
|
|
| orifice |
|
|
|
|
|
Burner backfiring during combustion | 1. | Burner orifice is clogged or damaged | 1. | Clean burner orifice (see Cleaning and |
|
|
|
| Maintenance, page 16) or replace burner |
|
|
|
| orifice |
| 2. | Burner damaged | 2. | Replace burner |
| 3. | Gas regulator defective | 3. | Replace gas regulator |
|
|
|
|
|
Burner plaque(s) does not glow (Infrared | 1. | Control knob set between locked positions | 1. | Turn control knob until it locks at de- |
models only) |
|
|
| sired setting |
| 2. | Inlet gas pressure is too low | 2. | Contact local natural or propane/LP gas |
|
|
|
| company |
| 3. | Plaque damaged | 3. | Replace burner |
|
|
|
|
|
Yellow flame during burner combustion | 1. | Not enough air | 1. | Check burner for dirt and debris. If |
|
|
|
| found, clean burner (see Cleaning and |
|
|
|
| Maintenance, page 16) |
| 2. | Inlet gas pressure is too low | 2. | Contact local natural or propane/LP gas |
|
|
|
| company |
| 3. | Gas regulator defective | 3. | Replace gas regulator |
|
|
|
|
|
Slight smoke or odor during initial operation | 1. | Residues from manufacturing processes | 1. | Problem will stop after a few hours of |
|
|
|
| operation |
|
|
|
|
|
Heater produces a whistling noise when | 1. | Turning control knob to HIGH position | 1. | Turn control knob to LOW position and |
burner is lit |
| when burner is cold |
| let warm up for a minute |
| 2. | Air in gas line | 2. | Operate burner until air is removed from |
|
|
|
| line. Have gas checked by local natural |
|
|
|
| or propane/LP gas company |
| 3. | Air passageways on heater blocked | 3. | Observe minimum installation clear- |
|
|
|
| ances (see Figure 4, page 7) |
| 4. | Dirty or partially clogged burner orifice | 4. | Clean burner (see Cleaning and Mainte- |
|
|
|
| nance, page 16) or replace burner orifice |
|
|
|
|
|
Heater produces a clicking/ticking noise just after burner is lit or shut off
1.Metal expanding while heating or con- tracting while cooling
1.This is common with most heaters. If noise is excessive, contact qualified ser- vice person
For more
visit www.
.com
