Desa GWN10T, GWRN10, GWN6, GWRP10, GWP10T Check GAS Type, Installation Items, Locating Heater

Page 6

6

INSTALLATION

Check Gas Type

INSTALLATION

NOTICE: This heater is intended for use as supple- mental heat. Use this heater along with your primary heating system. Do not install this heater as your primary heat source. If you have a central heating system, you may run system’s circulating blower while using heater. This will help circulate the heat throughout the house. In the event of a power outage, you can use this heater as your primary heat source.

WARNING: A qualified service person must in- stall heater. Follow all local codes.

CHECK GAS TYPE

Use only the correct type of gas (natural or propane/LP). If your gas supply is not the correct gas type, do not install heater. Call dealer where you bought heater for proper type heater.

INSTALLATION ITEMS

Before installing heater, make sure you have the items listed below.

•for propane/LP gas, external regulator (supplied by installer)

•piping (check local codes)

•sealant (resistant to propane/LP gas)

•equipment shutoff valve *

•ground joint union

•sediment trap

•tee joint

•pipe wrench

•for natural gas, test gauge connection*

*A CSA design-certified equipment shutoff valve with 1/8" NPT tap is an acceptable alternative to test gauge connection. Purchase the optional CSA design-certified equipment shutoff valve from your dealer. See Accessory, page 29.

LOCATING HEATER

This heater is designed to be mounted on a wall.

WARNING: Maintain the minimum clearances shown in Figure 4. If you can, provide greater clear- ances from floor, ceiling, and joining wall.

WARNING: Never install the heater

•in a bathroom (10,000 Btu/hr only. 6,000 Btu/hr mod- els are allowed in a bathroom. Check local codes.)

•in a recreational vehicle

•where curtains, furniture, clothing, or other flam- mable objects are less than 36 inches from the front, top, or sides of the heater

•as a fireplace insert

•in high traffic areas

•in windy or drafty areas

CAUTION: This heater creates warm air currents. These currents move heat to wall surfaces next to heater. Installing heater next to vinyl or cloth wall coverings or operating heater where impurities (such as but not limited to, tobacco smoke, aromatic candles, cleaning fluids, oil or kerosene lamps, etc.) in the air exist, may discolor walls or cause odors.

IMPORTANT: Vent-free heaters add moisture to the air. Al- though this is beneficial, installing heater in rooms without enough ventilation air may cause mildew to form from too much moisture. See Air for Combustion and Ventilation, pages 4 and 5.

CAUTION: If you install the heater in a home garage

•heater pilot and burner must be at least 18 inches above floor

•locate heater where moving vehicle will not hit it

For convenience and efficiency, install heater

•where there is easy access for operation, inspection, and service

•in coldest part of room

 

CEILING

6" Blueflame

36"

Minimum

8" Plaque

 

Minimum

 

From

 

Sides Of

 

Heater

 

 

Right

Left

Side

Side

 

3" Minimum To Top Surface

Of Carpeting, Tile Or Other

Combustible Material

Figure 4 - Mounting Clearances As Viewed From Front of Heater

For morevisit www..com

107902-01D

Page 5 Page 7
Image 6
Page 5 Page 7
Contents GWN6, GWP6 GWN10T, GWP10T GWRN10 and GWRP10What to do if YOU Smell GAS Table of Contents Safety InformationProduct Identification Product FeaturesUnpacking Local CodesAIR for Combustion and Ventilation Providing Adequate VentilationDetermining FRESH-AIR Flow for Heater Location Ventilation AIR Ventilation Air From Inside BuildingVentilation Air From Outdoors Check GAS Type InstallationInstallation Items Locating HeaterMarking Screw Locations Installing Heater to WallInstalling Two Mounting Screws Placing Heater On Mounting ScrewsConnecting to GAS Supply Installing Bottom Mounting ScrewRemoving Front Panel Of Heater Pressure Testing Gas Supply Piping System Checking GAS ConnectionsPressure Testing Heater Gas Connections Replace front panelOperating Heater Lighting InstructionsShutting Off Heater Manual Lighting ProcedureTo Turn OFF GAS To Appliance Shutting Off Burner Only pilot stays litTo Select Heating Level Burner PatternsThermostat Control Operation Burner Flame Pattern Blue Flame Models Inspecting BurnerPilot Flame Pattern Burner Flame Pattern Infrared ModelsODS/PILOT and Burner Orifice Cleaning MaintenanceCleaning Burner Pilot AIR Inlet Hole CabinetTroubleshooting Observed Problem Possible Cause RemedyMaintenance, Gas leak. See Warning statement at Illustrated Parts Breakdown GWP6 GWN6 GWP10 GWN10 PilotParts List KEY Part Number for GWP6 GWN6 GWP10 GWN10 Description QTYGWRP10 GWRN10 KEY Part Number GWRP10 GWRN10 Description QTY GWP10T GWN10T Pilot KEY Part Number GWP10T GWN10T Description QTY Specifications GWP6 GWP10 GWRP10 GWP10TTechnical Service Replacement PartsService Hints Service Publications AccessoryParts Centrals Baltimore ElectricOwners Registration Form Postage Required 107902-01D Warranty Information

GWN10T, GWP10T, GWRN10, GWN6, GWP6 specifications

Desa GWN10, GWP10, GWRP10, GWP6, and GWN6 are innovative products designed to meet diverse demands in various sectors. Each model brings unique features and characteristics, tailored for specific applications in the world of technology and daily use.

Desa GWN10 is recognized for its robust design and energy efficiency. It employs advanced wireless communication technology, enabling seamless integration with smart home systems. The GWN10 stands out with its high performance in terms of connectivity range and reliability. It offers users the convenience of remote monitoring and control, making it ideal for residential and commercial use, especially in areas that require a secure and efficient energy solution.

GWP10, on the other hand, is engineered for flexibility and versatility. Its modular design allows users to configure the system according to their specific needs. The GWP10 utilizes cutting-edge battery technology, providing longer usage times and faster charging capabilities. With its user-friendly interface and cloud connectivity, users can easily track energy consumption and optimize settings for enhanced performance.

The GWRP10 is a game-changer in renewable energy applications. Equipped with advanced solar integration technologies, it can harness solar power effectively, making it an eco-friendly choice. The GWRP10 features intelligent energy management systems that optimize power distribution, ensuring that energy is used efficiently. This model is perfect for users looking to reduce their carbon footprint while enjoying reliable power supply.

GWP6, a compact powerhouse, offers exceptional performance in a smaller footprint. Its lightweight construction and easy installation make it suitable for urban environments where space is a premium. The GWP6 leverages latest communication standards, such as IoT connectivity, providing real-time data insights for users. This makes it ideal for mobile applications and temporary installations.

Finally, the GWN6 emphasizes portability and ease of use. With its rugged design, it is perfect for outdoor activities and off-grid solutions. The GWN6 includes battery backup options, ensuring uninterrupted power during outdoor adventures. Its durable build and waterproof features make it reliable for challenging environments.

Together, these models showcase Desa’s commitment to innovation, sustainability, and user-centric design. Whether for energy management, renewable energy integration, or portable power, Desa GWN10, GWP10, GWRP10, GWP6, and GWN6 provide advanced solutions for contemporary needs. Their groundbreaking technologies and features are setting new standards in their respective categories, making them valuable assets for both everyday consumers and businesses alike.
Top Page Image Contents