Desa VTN25R, VTP22R Installing Batteries Into Remote, Replacing Battery in Ignitor

Page 9

INSTALLATION

Continued

Bottom View

Receiver Wire	Valve

Figure 7 - Connecting Receiver Wire

INSTALLING BATTERIES INTO REMOTE

1.Locate hand-held remote control in hardware bag included with your heater.

2.Remove battery cover and insert supplied batter- ies into remote control as shown in Figure 8.

3.Replace battery cover.

AAA

Batteries

Remote Control Battery Cover

Figure 8 - Installing Batteries in Hand- Held Remote Control

ACTIVATING COMMUNICATION BETWEEN RECEIVER AND REMOTE CONTROL

1.Set receiver selector switch to the remote position (see Figure 9).

2.Push the ON button on hand-held remote control. You should hear a beep. If not, use a dull object to push the LEARN button in the receiver (see Figure 9). Push the ON button on remote control once again. You may hear a series of beeps.

If you have questions regarding the remote control or receiver, call 1-888-672-8929.

	Slide Right to	LEARN Button (Inside)
	REMOTE	LEARN Button (Inside)
	REMOTE
		F
		ROOM SET TEMP
		ON	ON
		OFF	ON
		MODE	Button
		SET	Button
	Figure 9 - Receiver and Remote Control
		Setup

REPLACING BATTERY IN IGNITOR

If the spark that lights the pilot lessons, you may need to replace the battery in the ignitor. See Figure 10.

AAA Battery Negative towards cap

Figure 10 - Replacing Battery in Electronic Ignitor

MOUNTING HEATER BASE TO FLOOR (Where required by local codes)

1.Position heater in desired location. Mark holes for drilling. Move heater aside.

2.For carpeted ﬂoors, make a small cut with a sharp knife at the marked locations prior to drilling.

3.Drill 1/8" (diameter hole, 3/4" deep. (Do not use anchors in wood ﬂoors.)

4.For concrete ﬂoors, use 1/4" diameter concrete drill bit. Drill 1 3/8" deep. Insert anchors com- pletely into holes.

5.Position heater over holes. Secure to ﬂoor with wood screws. See Figure 11.

Wood

Screw

Mounting Hole (One each side)

Figure 11 - Mounting Heater to Floor

113261-01C

www.desatech.com

9

Image 9

Contents What to do if YOU Smell GAS Table of Contents Safety Information Local Codes Product FeaturesProduct Identification UnpackingAIR for Combustion Ventilation Providing Adequate VentilationDetermining FRESH-AIR Flow for Heater Location Ventilation Air From Inside Building Ventilation AIRInstallation Items InstallationCheck GAS Type Locating HeaterInstalling Remote Control Receiver Receiver AA Batteries Battery CoverReceiver Wire Bushing Connector Bracket Installing Batteries Into Remote Replacing Battery in IgnitorMounting Heater Base to Floor Where required by local codes Propane/LP External Supply Tank Regulator Vent Pointing Down Connecting to GAS SupplyChecking GAS Connections Test Pressures Equal To or Less Than 1/2 Psig 3.5 kPa Pressure Testing Heater GAS ConnectionsMake sure control knob of heater is in the OFF position ClosedOperating Heater For Your Safety Read Before LightingLighting Instructions Electronic Ignitor Auxiliary Pilot Knob ButtonHAND-HELD Remote Control Operation Manual Lighting ProcedureTo Turn OFF GAS To Appliance Thermostat OperationInspecting Heater Changing Set TemperaturePilot Flame Pattern Burner Flame PatternCleaning Maintenance Service HintsTechnical Service Observed Problem Possible Cause Remedy TroubleshootingProblem could be caused by Goes out when control knob isAssembly Delayed ignition of burners Manifold pressure is too lowGas leak. See Warning Models CTR25NR, VTN25R, CTR22PR and VTP22R Illustrated Parts BreakdownParts List Specifications AccessoryService Publications Replacement Parts FBD Parts CentralPatent Pending Modelos CTR25NR, CTR22PR, VTN25R Y VTP22R QUÉ Hacer SI Percibe Olor a GASInformación DE Seguridad Tabla DE ContenidoContinuación Identificación DEL Producto Códigos LocalesDesempaque Características DEL ProductoCómo Procurar LA Ventilación Adecuada Aire Para Combustión VentilaciónConstrucción inusualmente sellada Espacio conﬁnado o no conﬁnadoAire del interior de la construcción para ventilación Aire Para VentilaciónVerifique EL Tipo DE GAS InstalaciónArtículos DE Instalación Ubicación DEL CalentadorReceptor Baterías AA Instalación DEL Receptor DE Control RemotoCubierta de la batería Soporte del Conector Buje Del alambre ReceptorInstalación DE LAS Baterías EN EL Control Remoto Reemplazo DE LA Batería DEL EncendedorPRECAUCIÓNEnelcasodepro- pano o gas LP, nunca conecte el ca Conexión AL Suministro DE GASRevisión DE LAS Conexiones DE GAS Distribuidor. Consulte Accesorios, páginaRepare todas las fugas inmediatamente Abra la válvula de cierre del equipo consulte la ﬁgura Cierre la válvula de cierre del equipo consulte la ﬁguraVuelva a colocar el panel anterior Válvula dePara SU SEGURIDAD, LEA Esto Antes DE Encenderlo Funcionamiento DEL CalentadorInstrucciones DE Encendido Botón de encendido Perilla Auxiliar Del Piloto ElectrónicoProcedimiento DE Encendido Manual Funcionamiento DEL TermostatoFuncionamiento DEL Control Remoto Portátil Función ManualFunción DEL Termostato Room Inspección DEL CalentadorPatrón DE LA Llama DEL Piloto Patrón DE LA Llama DELServicio Técnico Limpieza Y MantenimientoProblema Observado Causa Posible Remedio Solución DE ProblemasCausa Posible Remedio Problema ObservadoImportante anterior Modelos CTR25NR, VTN25R, CTR22PR Y VTP22R Clasificación Ilustrada DE PiezasLista DE Piezas Accesorios EspecificacionesPublicaciones Para Servicio Válvula DE Cierre DEL Equipo GA5010Central DE Piezas Piezas DE RepuestoPiezas Bajo Garantía Piezas SIN Garantía113261-01 Rev. C 10/04 Patente en trámite