Quadra-Fire CB1200 Door Installation, CB 1200 Pellet Stove Thermostat Installation, Hand. Figure

Page 21

R

I. Door Installation

To install door:

1.Carefully remove door from packaging.

2.Line up hinges with hinge pins on appliance body, and slide door down until it sits securely on pins. Figure 21.1.

3.If door is plated, be sure to clean all plated surfaces and glass with a glass cleaner to ensure all oils are removed before your first burn.

4.Remove all labels from glass before burning appliance.

To adjust latches:

1.

Close door securely.

2.

Place rod in slot on the bracket on the door and close

 

latch.

3.

Latch must close tightly enough to ensure an airtight

 

seal between the door and the body of the appliance. To

 

increase tension on the latch, turn the rod clockwise a few

 

turns, then attempt to close the latch, until it is snug. Do not

 

overtighten; you should be able to close the latch with your

 

hand. Figure 21.2.

4.

After adjusting the latch, place a Phillips head screw driver

 

in the end of the rod, and tighten the nut with a wrench.

 

This will maintain the correct tension on the rod and latch.

Hinge Pin

Hinge

Figure 21.1

Rod and nut

Rod and nut

Figure 21.2

CB 1200 Pellet Stove

J. Thermostat Installation

1. A 12 volt AC thermostat is required to operate this pellet appliance. You may use the included wall mount thermo- stat or purchase an optional programmable thermostat or remote control. It is equipped with an adjustable heat anticipator. The current rating is .05 amps. The anticipator needs to be adjusted to the lowest setting available.

2.When mounting a thermostat on a wall, be sure to follow your thermostat installation instructions carefully.

NOTE: Thermostat must be mounted level for accurate readings. The thermostat should be mounted on an inside wall and not in direct line with the appliance convection air.

NOTE: If the thermostat is located too close to the appliance, you may need to set the temperature setting slightly higher to maintain the desired temperature in your home.

3.There is a 4 screw terminal block located on the back lower left corner of the stove directly above the power cord inlet. The center 2 screws are for the thermostat wires.

Power Outlet

Terminal Block.

Center 2 screws for

Thermostat Wires

Figure 21.3

Caution

Shock hazard.

• Do NOT remove grounding prong from plug.

•Plug directly into properly grounded 3 prong receptacle.

•Route cord away from appliance.

•Do NOT route cord under or in front of appliance.

September 21, 2006

7014-082B

Page 21

Page 20 Page 22
Image 21
Page 20 Page 22
Contents Classic BAY 1200 Pellet Stove Testing Lab & Report Number Serial Number Model Mfg Date CB 1200 Pellet StoveBehind left side curtain on outside of hopper wall Table of Contents Listing and Code Approvals Fire Safety Design, Installation & Location ConsiderationsGetting Started Appliance LocationCB 1200 Pellet Stove Tools And Supplies Needed Measuring StandardsInspect Appliance & Components and Pre-Use Check List Appliance Dimensions Dimensions and ClearancesCB 1200 Pellet Stove Clearances to Combustibles UL and ULC Exception for Horizontal Installations CB 1200 Pellet Stove Hearth Pad Requirements UL and ULCHearth Pad Requirements Vent Information Level of this installation. See Figure Pipe Selection ChartCB 1200 Pellet Stove Equivalent Feet of Pipe Example of 3 Elbow-Rear Vent Termination CalculatonAlcove 5Venting SystemsStraight Out DegreeCB 1200 Pellet Stove Through The Wall Through The Wall & Vertical CB 1200 Pellet Stove VerticalAlternate Masonry MasonryMobile Home Rear Installation Floor Installation Appliance Set-UpOutside Air Kit Instructions CB 1200 Pellet Stove Top Vent Adapter Installation Rear Vent and Rear Vent to Top Vent Adapter InstallationInstalling the Top Vent Adapter Brick Clip Installation CB 1200 Pellet Stove Brick Set InstallationCharred Areas in the Back Installing Logo Nickel OnlyLeft Twig Right Twig Front Log Holes. See FigureCB 1200 Pellet Stove Thermostat Installation Door InstallationTo install door To adjust latchesFuel Size And Material General Operating Information Operating InstructionsFuel Adjustment Rod Feed Rate Adjustment InstructionsStarting Your First Fire CB 1200 Pellet Stove Ignition Cycles Frequently Asked QuestionsTroubleshooting SymptomPossible Cause Corrective Action Page Page Maintaining & Servicing Your Appliance Cleaning Beneath Heat Exchanger Cleaning Heat Exchanger ChambersAsh Removal from Firebox Cont’d Disposal of Ashes Frequency As neededCleaning the Hopper Cleaning the Glass Frequency As neededCleaning Exhaust Blower Requires No Lubrication Cleaning Convection Blower Requires No LubricationConvection Blower Replacement CB 1200 Pellet Stove High Ash Fuel Content MaintenanceExhaust Blower Replacement Remove existing blower Install new blowerRe-install blower to blower housing Replacing Center Glass Replacing Side GlassScrews Reference Materials CB 200 Pellet StoveComponent Function & Location Wiring Harness See .1 below Vacuum SwitchSnap Disc #1 Convection Blower 145F Snap Disc #2 Thermostat Override 200FCB 1200 Pellet Stove Component Locations CB 1200 Pellet Stove Exploded Views Glass Size Center 13-7/8 wide x 11 highGlass Size Sides Nbr Description CB 1200 Pellet Stove Item # Parts Alphabetical Order CB 1200 Pellet Stove Service Parts and AccessoriesItem # Service Parts Alphabetical Order AccessoriesAppliance Date of Service Performed By Description of Service CB 1200 Pellet Stove Service And Maintenance LogCB 1200 Pellet Stove Warranty Policy Lifetime WarrantyTelephone Contact Information

CB1200 specifications

The Quadra-Fire CB1200 is a highly efficient and versatile wood-burning stove that stands out in the market for its innovative features and robust performance. With a focus on both functionality and aesthetics, the CB1200 aims to provide a comfortable, efficient heating solution while enhancing the beauty of any living space.

One of the main features of the Quadra-Fire CB1200 is its powerful heating capability. It boasts a maximum heat output of up to 80,000 BTUs, making it suitable for heating large areas within homes and cabins. The unit can efficiently heat spaces up to 2,500 square feet, offering reliable warmth even in the coldest climates. This impressive output is complemented by an extended burn time, allowing for longer periods between refueling, which adds convenience for users.

The CB1200 comes equipped with Quadra-Fire's renowned Advanced Combustion Technology. This cutting-edge system improves the efficiency of the fire by maximizing the combustion of gases and particles, leading to a cleaner burn with reduced emissions. This not only enhances the stove's overall performance but also provides a more environmentally friendly heating solution.

Another notable characteristic of the CB1200 is its user-friendly design. The large, glass door provides an excellent view of the fire, creating a warm and inviting ambiance while ensuring easy monitoring of fuel levels. The stove features a convenient ash pan for effortless cleanup, and the adjustable airflow control allows users to customize the burn intensity to suit their heating needs.

In addition to its performance features, the CB1200 is designed with durability in mind. Constructed from high-quality materials, it is built to withstand the rigors of regular use. The unit also offers various finishing options, enabling homeowners to select a style that complements their décor.

The Quadra-Fire CB1200 combines efficiency, beauty, and convenience, making it an exemplary choice for anyone seeking a wood-burning stove. With its impressive heating capabilities, advanced combustion technology, and user-friendly features, the CB1200 is designed to provide lasting comfort and satisfaction for its users, making it a worthwhile investment for any home.
Top Page Image Contents