Quadra-Fire CB1200 CB 1200 Pellet Stove Tools And Supplies Needed, Measuring Standards

Page 6

CB 1200 Pellet Stove

R

C. Tools And Supplies Needed

Tools and building supplies normally required for installation, unless installing into an existing masonry fireplace:

Reciprocating Saw

Safety Glasses

Channel Locks

Framing Square

Hammer

Electric Drill & Bits (1/4”)

Phillips Screwdriver

1/4” Self-Tapping Screws

Tape Measure

 

Plumb Line

May also need:

Level

Vent Support Straps

Framing Material

Venting Paint

Hi-temp Caulking Material

 

Gloves

 

D. Measuring Standards

1.Pipe measurements are from center line to center line.

2.Vertial terminations are measured to top of pipe.

Measure vertical

clearances from

this surface

Measure horizontal

clearances from

this surface

Figure 6.1

WARNING

Inspect appliance and components for damage. Damaged parts may impair safe operation.

Do NOT install damaged components.

Do NOT install incomplete components.

Do NOT install substitute components.

Report damaged parts to dealer.

E. Inspect Appliance & Components and Pre-Use Check List

1.

 

Place the appliance in a location near the

 

 

final installation area and follow the proce-

 

 

dures below:

2.

 

Open the appliance and remove all the parts

 

 

and articles packed inside the Component

 

 

Pack. Inspect all the parts and glass for ship-

 

 

ping damage. Contact your dealer if any irregu-

 

 

larities are noticed.

3.

 

All safety warnings have been read and fol-

 

 

lowed.

4.

 

This Owner’s Manual has been read.

5.

 

Floor protection requirements have been met.

6.

 

Venting is properly installed.

7.

 

The proper clearances from the appliance and

 

 

chimney to combustible materials have been

 

 

met.

8.

 

The masonry chimney is inspected by a profes-

 

 

sional and is clean, or the factory built metal

 

 

chimney is installed according to the manufac-

 

 

turer’s instructions and clearances.

9.

 

The chimney meets the required minimum

 

 

height.

10.

 

All labels have been removed from the glass

 

 

door.

11.

 

Plated surfaces have been wiped clean, if

 

 

applicable.

12.

 

Thermostat or remote has been installed.

13.

 

A power outlet is available nearby.

WARNING

Fire Risk.

Hearth & Home Technologies disclaims any responsibility for, and the warranty will be voided by, the following actions:

Installation and use of any damaged appliance.

Modification of the appliance.

Installation other than as instructed by Hearth & Home Technologies.

Installation and/or use of any component part not approved by Hearth & Home Technologies.

Operating appliance without fully assembling all components.

Operating appliance without legs attached (if supplied with unit).

Do NOT Overfire

Or any such action that may cause a fire hazard.

Page

7014-082B

September 21, 2006

Image 6
Contents Classic BAY 1200 Pellet Stove Testing Lab & Report Number Serial Number Model Mfg Date CB 1200 Pellet StoveBehind left side curtain on outside of hopper wall Table of Contents Listing and Code Approvals Getting Started Design, Installation & Location ConsiderationsFire Safety Appliance LocationCB 1200 Pellet Stove Tools And Supplies Needed Measuring StandardsInspect Appliance & Components and Pre-Use Check List Dimensions and Clearances Appliance DimensionsCB 1200 Pellet Stove Clearances to Combustibles UL and ULC Exception for Horizontal Installations CB 1200 Pellet Stove Hearth Pad Requirements UL and ULCHearth Pad Requirements Vent Information CB 1200 Pellet Stove Equivalent Feet of Pipe Pipe Selection ChartLevel of this installation. See Figure Example of 3 Elbow-Rear Vent Termination Calculaton5Venting Systems AlcoveStraight Out DegreeCB 1200 Pellet Stove Through The Wall CB 1200 Pellet Stove Vertical Through The Wall & VerticalMasonry Alternate MasonryMobile Home Rear Installation Floor Installation Appliance Set-UpOutside Air Kit Instructions CB 1200 Pellet Stove Top Vent Adapter Installation Rear Vent and Rear Vent to Top Vent Adapter InstallationInstalling the Top Vent Adapter CB 1200 Pellet Stove Brick Set Installation Brick Clip InstallationLeft Twig Right Twig Installing Logo Nickel OnlyCharred Areas in the Back Front Log Holes. See FigureTo install door Door InstallationCB 1200 Pellet Stove Thermostat Installation To adjust latchesOperating Instructions Fuel Size And Material General Operating InformationFuel Adjustment Rod Feed Rate Adjustment InstructionsStarting Your First Fire Frequently Asked Questions CB 1200 Pellet Stove Ignition CyclesTroubleshooting SymptomPossible Cause Corrective Action Page Page Maintaining & Servicing Your Appliance Ash Removal from Firebox Cont’d Cleaning Heat Exchanger ChambersCleaning Beneath Heat Exchanger Disposal of Ashes Frequency As neededCleaning Exhaust Blower Requires No Lubrication Cleaning the Glass Frequency As neededCleaning the Hopper Cleaning Convection Blower Requires No LubricationCB 1200 Pellet Stove High Ash Fuel Content Maintenance Convection Blower ReplacementExhaust Blower Replacement Remove existing blower Install new blowerRe-install blower to blower housing Replacing Center Glass Replacing Side GlassScrews Reference Materials CB 200 Pellet StoveComponent Function & Location Snap Disc #1 Convection Blower 145F Vacuum SwitchWiring Harness See .1 below Snap Disc #2 Thermostat Override 200FCB 1200 Pellet Stove Component Locations CB 1200 Pellet Stove Exploded Views Glass Size Center 13-7/8 wide x 11 highGlass Size Sides Nbr Description CB 1200 Pellet Stove CB 1200 Pellet Stove Service Parts and Accessories Item # Parts Alphabetical OrderItem # Service Parts Alphabetical Order AccessoriesAppliance CB 1200 Pellet Stove Service And Maintenance Log Date of Service Performed By Description of ServiceLifetime Warranty CB 1200 Pellet Stove Warranty PolicyContact Information Telephone

CB1200 specifications

The Quadra-Fire CB1200 is a highly efficient and versatile wood-burning stove that stands out in the market for its innovative features and robust performance. With a focus on both functionality and aesthetics, the CB1200 aims to provide a comfortable, efficient heating solution while enhancing the beauty of any living space.

One of the main features of the Quadra-Fire CB1200 is its powerful heating capability. It boasts a maximum heat output of up to 80,000 BTUs, making it suitable for heating large areas within homes and cabins. The unit can efficiently heat spaces up to 2,500 square feet, offering reliable warmth even in the coldest climates. This impressive output is complemented by an extended burn time, allowing for longer periods between refueling, which adds convenience for users.

The CB1200 comes equipped with Quadra-Fire's renowned Advanced Combustion Technology. This cutting-edge system improves the efficiency of the fire by maximizing the combustion of gases and particles, leading to a cleaner burn with reduced emissions. This not only enhances the stove's overall performance but also provides a more environmentally friendly heating solution.

Another notable characteristic of the CB1200 is its user-friendly design. The large, glass door provides an excellent view of the fire, creating a warm and inviting ambiance while ensuring easy monitoring of fuel levels. The stove features a convenient ash pan for effortless cleanup, and the adjustable airflow control allows users to customize the burn intensity to suit their heating needs.

In addition to its performance features, the CB1200 is designed with durability in mind. Constructed from high-quality materials, it is built to withstand the rigors of regular use. The unit also offers various finishing options, enabling homeowners to select a style that complements their décor.

The Quadra-Fire CB1200 combines efficiency, beauty, and convenience, making it an exemplary choice for anyone seeking a wood-burning stove. With its impressive heating capabilities, advanced combustion technology, and user-friendly features, the CB1200 is designed to provide lasting comfort and satisfaction for its users, making it a worthwhile investment for any home.