Quadra-Fire CB1200 Exhaust Blower Replacement Remove existing blower, Install new blower

Page 32

CB 1200 Pellet Stove

R

2.Exhaust Blower Replacement

Remove existing blower:

a. Use proper shut down procedures to shut down the appli- ance and let it completely cool and then unplug it.

b.Use an 11/32" wrench or nut driver to loosen and remove the (6) nuts holding motor mount plate to the blower housing on your stove.

c.Remove washer from beneath the terminal ring on the grounding wire.

d.Pull motor/mounting plate from blower housing.

e.Scrape off old gasketing material from blower housing.

Install new blower:

f.The blower and blower housing is shipped as a unit. It is necessary to separate them at this point if you are using the existing blower housing already installed on the appliance:

g.Follow steps 2 and 3 above. Discard or set aside the new blower housing.

h.Carefully remove gasketing from new housing and set onto the blower housing.

Re-install blower to blower housing:

i. Install blower on housing ensuring that wiring exits facing the 8 o’clock position. Place the washer and then the grounding wire on nearest mounting plate stud.

j.Use nuts removed in step b to secure blower to hous- ing.

k.Re-connect wiring (use jumper wire if necessary). Re- connect power supply.

E. Igniter Replacement

Igniter Bracket

 

Thumb Screw

Igniter

Figure 32.1

1.Use proper shut down procedures to shut down the appliance and let it completely cool down and then unplug it and remove the ash drawer.

2.Follow instructions to remove the ash drawer found on page 28. Remove the access plate directly above it by removing the 2 screws just below the ash catcher.

3.The wire leads to the igniter are connected to the wire harness with 1/4 inch male / female spade connectors. These wires will pull forward approximately 4 to 5 inches (102mm to 127mm). Disconnect the spade connections and remove the igniter from the chamber. Loosen the thumb screw and slide igniter out.

4.Install new igniter into the chamber and tighten the thumb screw. Re-connect the wires to the 2 leads with the spade connectors.

5.Remove right side panel and pull wire leads back toward the rear of the appliance to take-up the 4 to 5 inches (102mm to 107mm) previously pulled out. This will keep the wires out of the way of the ash drawer. Double check that the igniter wires are clear of any movement, i.e. ash drawer, firepot cleaning rod, etc.

6.Re-install the ash drawer and side panel and re-connect the power.

F.Baffle Removal

1.Use proper shut down procedures to shut down the appliance and let it completely cool down.

2.Open right side panel and then open the door.

3.The 2 baffles are located at the top inside of firebox.

4.Place your hand on the baffle and slide it up and the bottom edge will fall down and then you can lift the baffle out. Repeat for the other side.

Page 32

7014-082B

September 21, 2006

Page 31 Page 33
Image 32
Page 31 Page 33
Contents Classic BAY 1200 Pellet Stove Behind left side curtain on outside of hopper wall Testing Lab & Report Number Serial Number Model Mfg DateCB 1200 Pellet Stove Table of Contents Listing and Code Approvals Design, Installation & Location Considerations Fire SafetyGetting Started Appliance LocationInspect Appliance & Components and Pre-Use Check List CB 1200 Pellet Stove Tools And Supplies NeededMeasuring Standards Dimensions and Clearances Appliance DimensionsCB 1200 Pellet Stove Clearances to Combustibles UL and ULC Hearth Pad Requirements Exception for Horizontal InstallationsCB 1200 Pellet Stove Hearth Pad Requirements UL and ULC Vent Information Pipe Selection Chart Level of this installation. See FigureCB 1200 Pellet Stove Equivalent Feet of Pipe Example of 3 Elbow-Rear Vent Termination Calculaton5Venting Systems AlcoveCB 1200 Pellet Stove Through The Wall Straight OutDegree CB 1200 Pellet Stove Vertical Through The Wall & VerticalMasonry Alternate MasonryMobile Home Outside Air Kit Instructions Rear Installation Floor InstallationAppliance Set-Up Installing the Top Vent Adapter CB 1200 Pellet Stove Top Vent Adapter InstallationRear Vent and Rear Vent to Top Vent Adapter Installation CB 1200 Pellet Stove Brick Set Installation Brick Clip InstallationInstalling Logo Nickel Only Charred Areas in the BackLeft Twig Right Twig Front Log Holes. See FigureDoor Installation CB 1200 Pellet Stove Thermostat InstallationTo install door To adjust latchesOperating Instructions Fuel Size And Material General Operating InformationStarting Your First Fire Fuel Adjustment RodFeed Rate Adjustment Instructions Frequently Asked Questions CB 1200 Pellet Stove Ignition CyclesPossible Cause Corrective Action TroubleshootingSymptom Page Page Maintaining & Servicing Your Appliance Cleaning Heat Exchanger Chambers Cleaning Beneath Heat ExchangerAsh Removal from Firebox Cont’d Disposal of Ashes Frequency As neededCleaning the Glass Frequency As needed Cleaning the HopperCleaning Exhaust Blower Requires No Lubrication Cleaning Convection Blower Requires No LubricationCB 1200 Pellet Stove High Ash Fuel Content Maintenance Convection Blower ReplacementRe-install blower to blower housing Exhaust Blower Replacement Remove existing blowerInstall new blower Screws Replacing Center GlassReplacing Side Glass Component Function & Location Reference MaterialsCB 200 Pellet Stove Vacuum Switch Wiring Harness See .1 belowSnap Disc #1 Convection Blower 145F Snap Disc #2 Thermostat Override 200FCB 1200 Pellet Stove Component Locations Glass Size Sides CB 1200 Pellet Stove Exploded ViewsGlass Size Center 13-7/8 wide x 11 high Nbr Description CB 1200 Pellet Stove CB 1200 Pellet Stove Service Parts and Accessories Item # Parts Alphabetical OrderAppliance Item # Service Parts Alphabetical OrderAccessories CB 1200 Pellet Stove Service And Maintenance Log Date of Service Performed By Description of ServiceLifetime Warranty CB 1200 Pellet Stove Warranty PolicyContact Information Telephone

CB1200 specifications

The Quadra-Fire CB1200 is a highly efficient and versatile wood-burning stove that stands out in the market for its innovative features and robust performance. With a focus on both functionality and aesthetics, the CB1200 aims to provide a comfortable, efficient heating solution while enhancing the beauty of any living space.

One of the main features of the Quadra-Fire CB1200 is its powerful heating capability. It boasts a maximum heat output of up to 80,000 BTUs, making it suitable for heating large areas within homes and cabins. The unit can efficiently heat spaces up to 2,500 square feet, offering reliable warmth even in the coldest climates. This impressive output is complemented by an extended burn time, allowing for longer periods between refueling, which adds convenience for users.

The CB1200 comes equipped with Quadra-Fire's renowned Advanced Combustion Technology. This cutting-edge system improves the efficiency of the fire by maximizing the combustion of gases and particles, leading to a cleaner burn with reduced emissions. This not only enhances the stove's overall performance but also provides a more environmentally friendly heating solution.

Another notable characteristic of the CB1200 is its user-friendly design. The large, glass door provides an excellent view of the fire, creating a warm and inviting ambiance while ensuring easy monitoring of fuel levels. The stove features a convenient ash pan for effortless cleanup, and the adjustable airflow control allows users to customize the burn intensity to suit their heating needs.

In addition to its performance features, the CB1200 is designed with durability in mind. Constructed from high-quality materials, it is built to withstand the rigors of regular use. The unit also offers various finishing options, enabling homeowners to select a style that complements their décor.

The Quadra-Fire CB1200 combines efficiency, beauty, and convenience, making it an exemplary choice for anyone seeking a wood-burning stove. With its impressive heating capabilities, advanced combustion technology, and user-friendly features, the CB1200 is designed to provide lasting comfort and satisfaction for its users, making it a worthwhile investment for any home.
Top Page Image Contents