Quadra-Fire CB1200 Getting Started, Design, Installation & Location Considerations, Fire Safety

Page 5

R

CB 1200 Pellet Stove

 

 

 

 

2 Getting Started

 

A.Design, Installation & Location Considerations

1.Appliance Location

Consideration must be given to safety, convenience, traffic flow, and the fact that the appliance will need a chimney and chimney connector. It is a good idea to plan your installation on paper, using exact measurements for clearances and floor protection, before actually beginning the installation. If you are not using an existing chimney, place the appliance where there will be a clear passage for a factory-built listed chimney through the ceiling and roof.

Check with your local building code agency before you begin your installation. Be sure local building codes do not supersede UL specifications and always obtain a building permit so that insurance protection benefits cannot be unexpectedly cancelled. If any assistance is required during installation, please contact your local dealer.

We recommend that a qualified building inspector and your insurance company representative review your plans before and after installation.

2. Thermostat Location

The thermostat’s location will have some effect on the appliance’s operation. When the thermostat is located close to the appliance, it may require a slightly higher temperature setting to keep the rest of the house comfortable. If the thermostat location is in an adjacent room or on a different floor level, you will notice higher temperatures near the appliance.

CAUTION

•Do NOT connect this unit to a chimney flue servicing another appliance.

•Do NOT connect to any air distribution duct or system.

B. Fire Safety

Maintain the designated clearances to combustibles. Insu- lation must not touch the chimney. You must maintain the designated air space clearance around the chimney. This space around a chimney is necessary to allow natural heat removal from the area. Insulation in this space will cause a heat buildup, which may ignite wood framing. NOTE:

Clearances may only be reduced by means approved by the regulatory authority having jurisdiction.

To provide reasonable fire safety, the following should be given serious consideration:

1.Install at least one smoke detector on each floor of your home to ensure your safety. They should be located away from the heating appliance and close to the sleeping areas. Follow the smoke detector manufacturer’s placement and installation instructions, and be sure to maintain regularly.

2.A conveniently located Class A fire extinguisher to contend with small fires resulting from burning embers.

3.A practiced evacuation plan, consisting of at least 2 escape routes.

4.A plan to deal with a hopper fire as follows: In the event of a hopper fire:

a.Notify fire department

b.Prepare occupants for immediate evacuation.

c.Close all openings into the appliance.

d.Unplug appliance.

e.While awaiting fire department, watch for ignition of adjacent combustibles from overheated vent pipe, hot embers or sparks from the chimney.

f.Pour a bucket of water into the appliance hopper.

WARNING

Fire Hazard.

•Do not operate appliance before reading and understanding operating instructions.

•Failure to operate appliance properly may cause a house fire.

September 21, 2006

7014-082B

Page

Page 4 Page 6
Image 5
Page 4 Page 6
Contents Classic BAY 1200 Pellet Stove Behind left side curtain on outside of hopper wall Testing Lab & Report Number Serial Number Model Mfg DateCB 1200 Pellet Stove Table of Contents Listing and Code Approvals Fire Safety Design, Installation & Location ConsiderationsGetting Started Appliance LocationInspect Appliance & Components and Pre-Use Check List CB 1200 Pellet Stove Tools And Supplies NeededMeasuring Standards Appliance Dimensions Dimensions and ClearancesCB 1200 Pellet Stove Clearances to Combustibles UL and ULC Hearth Pad Requirements Exception for Horizontal InstallationsCB 1200 Pellet Stove Hearth Pad Requirements UL and ULC Vent Information Level of this installation. See Figure Pipe Selection ChartCB 1200 Pellet Stove Equivalent Feet of Pipe Example of 3 Elbow-Rear Vent Termination CalculatonAlcove 5Venting SystemsCB 1200 Pellet Stove Through The Wall Straight OutDegree Through The Wall & Vertical CB 1200 Pellet Stove VerticalAlternate Masonry MasonryMobile Home Outside Air Kit Instructions Rear Installation Floor InstallationAppliance Set-Up Installing the Top Vent Adapter CB 1200 Pellet Stove Top Vent Adapter InstallationRear Vent and Rear Vent to Top Vent Adapter Installation Brick Clip Installation CB 1200 Pellet Stove Brick Set InstallationCharred Areas in the Back Installing Logo Nickel OnlyLeft Twig Right Twig Front Log Holes. See FigureCB 1200 Pellet Stove Thermostat Installation Door InstallationTo install door To adjust latchesFuel Size And Material General Operating Information Operating InstructionsStarting Your First Fire Fuel Adjustment RodFeed Rate Adjustment Instructions CB 1200 Pellet Stove Ignition Cycles Frequently Asked QuestionsPossible Cause Corrective Action TroubleshootingSymptom Page Page Maintaining & Servicing Your Appliance Cleaning Beneath Heat Exchanger Cleaning Heat Exchanger ChambersAsh Removal from Firebox Cont’d Disposal of Ashes Frequency As neededCleaning the Hopper Cleaning the Glass Frequency As neededCleaning Exhaust Blower Requires No Lubrication Cleaning Convection Blower Requires No LubricationConvection Blower Replacement CB 1200 Pellet Stove High Ash Fuel Content MaintenanceRe-install blower to blower housing Exhaust Blower Replacement Remove existing blowerInstall new blower Screws Replacing Center GlassReplacing Side Glass Component Function & Location Reference MaterialsCB 200 Pellet Stove Wiring Harness See .1 below Vacuum SwitchSnap Disc #1 Convection Blower 145F Snap Disc #2 Thermostat Override 200FCB 1200 Pellet Stove Component Locations Glass Size Sides CB 1200 Pellet Stove Exploded ViewsGlass Size Center 13-7/8 wide x 11 high Nbr Description CB 1200 Pellet Stove Item # Parts Alphabetical Order CB 1200 Pellet Stove Service Parts and AccessoriesAppliance Item # Service Parts Alphabetical OrderAccessories Date of Service Performed By Description of Service CB 1200 Pellet Stove Service And Maintenance LogCB 1200 Pellet Stove Warranty Policy Lifetime WarrantyTelephone Contact Information

CB1200 specifications

The Quadra-Fire CB1200 is a highly efficient and versatile wood-burning stove that stands out in the market for its innovative features and robust performance. With a focus on both functionality and aesthetics, the CB1200 aims to provide a comfortable, efficient heating solution while enhancing the beauty of any living space.

One of the main features of the Quadra-Fire CB1200 is its powerful heating capability. It boasts a maximum heat output of up to 80,000 BTUs, making it suitable for heating large areas within homes and cabins. The unit can efficiently heat spaces up to 2,500 square feet, offering reliable warmth even in the coldest climates. This impressive output is complemented by an extended burn time, allowing for longer periods between refueling, which adds convenience for users.

The CB1200 comes equipped with Quadra-Fire's renowned Advanced Combustion Technology. This cutting-edge system improves the efficiency of the fire by maximizing the combustion of gases and particles, leading to a cleaner burn with reduced emissions. This not only enhances the stove's overall performance but also provides a more environmentally friendly heating solution.

Another notable characteristic of the CB1200 is its user-friendly design. The large, glass door provides an excellent view of the fire, creating a warm and inviting ambiance while ensuring easy monitoring of fuel levels. The stove features a convenient ash pan for effortless cleanup, and the adjustable airflow control allows users to customize the burn intensity to suit their heating needs.

In addition to its performance features, the CB1200 is designed with durability in mind. Constructed from high-quality materials, it is built to withstand the rigors of regular use. The unit also offers various finishing options, enabling homeowners to select a style that complements their décor.

The Quadra-Fire CB1200 combines efficiency, beauty, and convenience, making it an exemplary choice for anyone seeking a wood-burning stove. With its impressive heating capabilities, advanced combustion technology, and user-friendly features, the CB1200 is designed to provide lasting comfort and satisfaction for its users, making it a worthwhile investment for any home.
Top Page Image Contents